2011-2013 Land Cruiser · Service Manual Vehicle Interior

Engine Switch Indicator Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

Engine switch condition (power source mode) or system malfunctions can be checked by observing the status of the engine switch indicator light.
Engine Switch Indicator Light Condition 
Power Source Mode/Condition
Indicator Light Condition
Brake pedal released (for A/T)
Clutch pedal released (for M/T)
Brake pedal depressed, shift lever in P or N (for A/T)
Clutch pedal depressed (for M/T)
Off
Off
Illuminates (Green)
Illuminates (Green)
On (ACC, IG)
Illuminates (Amber)
Illuminates (Green)
Illuminates (Green)
Engine running
Off
Off
Off
Steering lock not unlocked
Flashes (Green) for 30 sec.
Flashes (Green) for 30 sec.
Flashes (Green) for 30 sec.
System malfunction
Flashes (Amber) for 15 sec.
Flashes (Amber) for 15 sec.
Flashes (Amber) for 15 sec.
Clutch start switch malfunction (for M/T)
Flashes (Green) for 15 sec.
Flashes (Green) for 15 sec.
Flashes (Green) for 15 sec.

WIRING DIAGRAM

C165204E03

INSPECTION PROCEDURE


1. INSPECT ENGINE SWITCH
C164809E05
  1. Disconnect the E18 engine switch connector.

  1. Apply battery voltage between the terminals of the engine switch, and check the illumination condition of the engine switch indicator light.

    NOTICE:
    1. If the positive (+) lead and the negative (-) lead are incorrectly connected, the engine switch indicator light will not illuminate.
    2. If the voltage is too low, the indicator light will not illuminate.

    OK:
    Measurement Condition
    Condition
    Specified Condition
    Battery terminal (+) → Terminal 11 (SWIL) - Battery terminal (-) → Terminal 5 (GND)
    Battery voltage is applied to the terminals
    Illuminates
    Battery terminal (+) → Terminal 12 (INDS) - Battery terminal (-) → Terminal 5 (GND)
    Battery terminal (+) → Terminal 13 (INDW) - Battery terminal (-) → Terminal 5 (GND)

    Result 
    Result
    Proceed to
    Illuminates
    A
    Does not illuminate (for 1GR-FE)
    B
    Does not illuminate (for 2UZ-FE)
    C
    Does not illuminate (for 3UR-FE)
    D
    Does not illuminate (for 1VD-FTV)
    E



B
REPLACE ENGINE SWITCH (Click here)

C
REPLACE ENGINE SWITCH (Click here)

D
REPLACE ENGINE SWITCH (Click here)

E
REPLACE ENGINE SWITCH (Click here)
A


2. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ENGINE SWITCH AND BODY GROUND)
C162990E05
  1. Disconnect the E1 main body ECU connector.

  1. Disconnect the E18 engine switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E1-25 (SWIL) - E18-11 (SWIL)
    Always
    Below 1 Ω
    E1-15 (INDS) - E18-12 (INDS)
    Always
    Below 1 Ω
    E1-14 (INDW) - E18-13 (INDW)
    Always
    Below 1 Ω
    E18-5 (GND) - Body ground
    Always
    Below 1 Ω
    E1-25 (SWIL) or E18-11 (SWIL) - Body ground
    Always
    10 kΩ or higher
    E1-15 (INDS) or E18-12 (INDS) - Body ground
    Always
    10 kΩ or higher
    E1-14 (INDW) or E18-13 (INDW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← Engine does not Start (from Jan 2012)Engine Switch Indicator Circuit (from Jan 2012) →