B1810/53 Short in Driver Side Squib 2nd Step Circuit
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Also covers:
- B1811/53 Open in Driver Side Squib 2nd Step Circuit
- B1812/53 Short to GND in Driver Side Squib 2nd Step Circuit
- B1813/53 Short to B+ in Driver Side Squib 2nd Step Circuit
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The driver side squib 2nd step circuit consists of the center airbag sensor, the spiral cable, and the steering pad.The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the driver side squib 2nd step circuit.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B1810/53 |
When one of the following conditions is met:
|
|
| B1811/53 |
When one of the following conditions is met:
|
|
| B1812/53 |
When one of the following conditions is met:
|
|
| B1813/53 |
When one of the following conditions is met:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
- HINT:
- To perform the simulation method, enter the check mode (signal check) with the intelligent tester (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (Click here).
| 1. CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP) |
Turn the ignition switch off.


Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the steering pad.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).
- CAUTION:
- Never connect the tester to the steering pad (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.
- NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting SST.
- Insert SST straight into the terminals of the connector.
- Do not forcibly insert SST into the terminals of the connector when connecting SST.
- SST
- 09843-18061
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1810, B1811, B1812 or B1813 is not output.
- HINT:
- Codes other than DTC B1810, B1811, B1812 and B1813 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
| 2. CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector E.
Check that the spiral cable connectors (on the steering pad side) are not damaged.
- OK:
- The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
|
|
||||
| OK | |
| 3. CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT |
Disconnect the connectors from the center airbag sensor.


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
z38-1 - Body ground
Ignition switch ON
Below 1 V
z38-2 - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
z38-1 - z38-2
Always
Below 1 Ω
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
z38-1 - z38-2
Always
1 MΩ or higher
z38-1 - Body ground
Always
1 MΩ or higher
z38-2 - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | |
| 4. CHECK CENTER AIRBAG SENSOR |
Connect the connectors to the steering pad and the center airbag sensor.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1810, B1811, B1812 or B1813 is not output.
- HINT:
- Codes other than DTC B1810, B1811, B1812 and B1813 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
| 5. CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE) |
Restore the released activation prevention mechanism of connector B to its original condition.


Disconnect the instrument panel wire connector from the spiral cable.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E13-4 (D2+) - Body ground
Ignition switch ON
Below 1 V
E13-3 (D2-) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E13-4 (D2+) - E13-3 (D2-)
Always
Below 1 Ω
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E13-4 (D2+) - E13-3 (D2-)
Always
1 MΩ or higher
E13-4 (D2+) - Body ground
Always
1 MΩ or higher
E13-3 (D2-) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | ||
| ||
