2011-2013 Land Cruiser · Service Manual Steering

C15A2/62 Actuator Malfunction

Diagnostic trouble codes · Vehicles built from Jan 2012

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The steering control ECU drives the actuator based on steering angle sensor signals and vehicle speed signals.
If the steering control ECU detects excessive current flowing into the steering actuator, or an internal malfunction, it will turn on the master warning light, store DTC C15A2/62, and stop VGRS operation.
If the steering control ECU detects a malfunction in the motor drive circuit, it will turn the master warning light on, store DTC C15A6/62, and stop VGRS operation.
DTC Code
DTC Detection Condition
Trouble Area
C15A2/62
The VGRS system detects a malfunction in the motor drive circuit.
  1. Harness or connector
  2. Power source circuit
  3. Steering actuator
  4. Steering control ECU
C15A6/62
The actual motor current value greatly differs from the estimated value.
  1. Power source circuit
  2. Harness or connector
  3. Steering actuator
  4. Steering control ECU

WIRING DIAGRAM

C163900E04

INSPECTION PROCEDURE

HINT:
Only the actuator only can be checked in this procedure. If it is normal, the steering control ECU is faulty.


1. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
C149134E13
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E77-7 (PGND) - Body ground
    Always
    Below 1 Ω
    E78-8 (PGD2) - Body ground

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E77-8 (PIG) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (STEERING CONTROL ECU - STEERING ACTUATOR)
C175599E01
  1. Disconnect the E78 steering control ECU connector.

  1. Disconnect the E80 steering actuator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E78-1 (BMV) - E78-2 (BMU)
    Always
    10 kΩ or higher
    E78-1 (BMV) - E78-3 (BMW)
    E78-2 (BMU) - E78-3 (BMW)
    E78-1 (BMV) - E80-5 (BMV+)
    Always
    Below 1 Ω
    E78-2 (BMU) - E80-4 (BMU+)
    E78-3 (BMW) - E80-13 (BMW+)
    E78-1 (BMV) - Body ground
    Always
    10 kΩ or higher
    E78-2 (BMU) - Body ground
    E78-3 (BMW) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK STEERING ACTUATOR

  1. C149144E03
    Disconnect the E78 steering control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured with the steering actuator connector connected.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E78-1 (BMV) - E78-2 (BMU)
    Always
    Below 1 Ω
    E78-1 (BMV) - E78-3 (BMW)
    E78-2 (BMU) - E78-3 (BMW)
    E78-1 (BMV) - Body ground
    Always
    10 kΩ or higher
    E78-2 (BMU) - Body ground
    E78-3 (BMW) - Body ground



NG
REPLACE STEERING ACTUATOR ASSEMBLY (Click here)
OK


4. CHECK DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    C15A1/61 is output
    A
    C15A1/61 is not output (for LHD)
    B
    C15A1/61 is not output (for RHD)
    C



B
REPLACE STEERING CONTROL ECU (Click here)

C
REPLACE STEERING CONTROL ECU (Click here)
A

REPLACE STEERING ACTUATOR ASSEMBLY (Click here)


← C15A2/62 Actuator Malfunction (+ C15A6/62) (Sep 2011 – Dec 2011)C15A3/63 Actuator Malfunction (+ C15C5/69) (from Sep 2011) →