2011-2013 Land Cruiser · Service Manual Steering

C15A3/63 Actuator Malfunction

Diagnostic trouble codes · Vehicles built from Sep 2011

Also covers:

DESCRIPTION

The steering actuator drives the internal motor using the current output from the steering control ECU to change the relative angle between the tire angle and steering wheel angle.
The rotation angle sensor in the steering actuator detects the motor rotation angle and outputs this information to the steering control ECU.
If the steering control ECU detects a malfunction in the rotation angle sensor circuit, it will store DTC C15A3/63.
DTC Code
DTC Detection Condition
Trouble Area
C15A3/63
The steering control ECU detects a malfunction in the rotation angle sensor circuit.
  1. Harness or connector
  2. Steering actuator
  3. Steering control ECU
C15C5/69
A steering signal indicating a motor rotation angle of 36° or more (to the left or right) is input after entering test mode.*
  1. Harness or connector
  2. Steering actuator
  3. Steering control ECU

HINT:
*: A tire angle of 36° and a motor rotation angle of 36° correspond to the steering wheel angle. The amount of change in tire angle and motor rotation angle is from when the mode is changed to test mode.


WIRING DIAGRAM

C163901E05

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (STEERING CONTROL ECU - STEERING ACTUATOR)
C175600E01
  1. Disconnect the E79 steering control ECU connector.

  1. Disconnect the E80 steering actuator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E79-4 (S1) - E80-2 (S1+)
    Always
    Below 1 Ω
    E79-6 (RV) - E80-1 (RV+)
    E79-14 (S2) - E80-9 (S2+)
    E79-15 (RG) - E80-10 (RG+)
    E79-4 (S1) - E79-6 (RV)
    Always
    10 kΩ or higher
    E79-4 (S1) - E79-14 (S2)
    E79-4 (S1) - E79-15 (RG)
    E79-6 (RV) - E79-14 (S2)
    E79-6 (RV) - E79-15 (RG)
    E79-14 (S2) - E79-15 (RG)
    E79-4 (S1) - Body ground
    E79-6 (RV) - Body ground
    E79-14 (S2) - Body ground
    E79-15 (RG) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK STEERING ACTUATOR

  1. C149150E02
    Disconnect the E79 steering control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured with the steering actuator connector connected.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E79-4 (S1) - E79-6 (RV)
    Always
    Below 200 Ω
    E79-4 (S1) - E79-14 (S2)
    E79-4 (S1) - E79-15 (RG)
    E79-6 (RV) - E79-14 (S2)
    E79-6 (RV) - E79-15 (RG)
    E79-14 (S2) - E79-15 (RG)
    E79-4 (S1) - Body ground
    Always
    10 kΩ or higher
    E79-6 (RV) - Body ground
    E79-14 (S2) - Body ground
    E79-15 (RG) - Body ground

    Result 
    Result
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD)
    C



B
REPLACE STEERING CONTROL ECU (Click here)

C
REPLACE STEERING CONTROL ECU (Click here)
A

REPLACE STEERING ACTUATOR ASSEMBLY (Click here)


← C15A2/62 Actuator Malfunction (+ C15A6/62) (from Jan 2012)C15A4/64 Actuator Malfunction (+ C15A9/66, C15AA/66, C15AB/66) (from Sep 2011) →