2011-2013 Land Cruiser · Service Manual Steering

C15C1/74 Steering Angle Sensor Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The steering control ECU detects a steering angle sensor malfunction by receiving an error signal from the steering angle sensor via CAN communication. If the steering control ECU detects this error signal, it will turn the master warning light on, store these DTCs, and stop VGRS operation.
DTC Code
DTC Detection Condition
Trouble Area
C15C1/74
The steering control ECU receives a steering angle sensor malfunction signal via CAN communication.
  1. Steering angle sensor
  2. Harness or connector
  3. CAN communication system
  4. Steering control ECU
C15C2/74
The steering control ECU receives a B+ open circuit signal from the steering angle sensor via CAN communication.
  1. Steering angle sensor
  2. Harness or connector
  3. CAN communication system
  4. Steering control ECU

WIRING DIAGRAM

C149147E16

INSPECTION PROCEDURE


1. CHECK DTC (CAN COMMUNICATION SYSTEM)
  1. Using the intelligent tester, check if the CAN communication system is functioning normally (Click here for LHD, Click here for RHD).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output (for LHD)
    B
    DTC is output (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) (Click here)
A


2. CHECK HARNESS AND CONNECTOR (STEERING CONTROL ECU +BI TERMINAL VOLTAGE)

  1. C149134E39
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E77-10 (+BI) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK STEERING CONTROL ECU (+BO TERMINAL VOLTAGE)

  1. C149134E11
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E79-1 (+BO) - Body ground
    Always
    11 to 14 V

    Result 
    Result
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE STEERING CONTROL ECU (Click here)

C
REPLACE STEERING CONTROL ECU (Click here)
A


4. CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR)

  1. G030156E44
    Disconnect the E11 steering angle sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E11-1 (IG) - Body ground
    Engine switch on (IG)
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E11-2 (ESS) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK STEERING ANGLE SENSOR

  1. G030156E45
    Disconnect the E11 steering angle sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E11-3 (BAT) - E11-2 (ESS)
    Engine switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEERING ANGLE SENSOR (Click here)


← C15B4/71 ECU Malfunction (from Jan 2012)C15C1/74 Steering Angle Sensor Malfunction (+ C15C2/74) (from Jan 2012) →