2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

HOW TO PROCEED WITH TROUBLESHOOTING

Troubleshooting · Vehicles built Sep 2011 – Dec 2011

HINT:
  1. Use the following procedure to troubleshoot the navigation system (for HDD).
  2. *: Use the intelligent tester.


1.VEHICLE BROUGHT TO WORKSHOP
    NEXT

    2.INSPECT BATTERY VOLTAGE
    1. Inspect the battery voltage.

      Standard Voltage:
      11 to 14 V

      If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

    NEXT

    3.DIAGNOSTIC QUESTIONING AND SYMPTOM CONFIRMATION
    1. Ask the customer about symptoms and confirm malfunctions.

      Result 
      Result
      Proceed to
      Other symptoms.
      A
      The screen displays nothing.
      B


    B.
    A

    4.OPERATION CHECK
    1. Refer to Check System Normal Condition (Click here).

      Result 
      Result
      Proceed to
      Symptom is not normal operation.
      A
      Symptom is normal operation.
      B


    B.
    A

    5.CHECK CAN COMMUNICATION SYSTEM*
    1. Check for DTC output.

      HINT:
      1. for LHD (Click here)
      2. for RHD (Click here)

      Result 
      Result
      Proceed to
      DTC is not output.
      A
      DTC is output. (for LHD)
      B
      DTC is output. (for RHD)
      C


    B.

    C.
    A

    6.CHECK FOR DTC*
    1. Refer to DTC Check/Clear (Click here).

      Result 
      Result
      Proceed to
      DTC is output.
      A
      DTC is not output.
      B

    2. HINT:
      If more information is needed, perform a recheck using the "System Check Mode" screen after rechecking for DTCs using the intelligent tester (Click here).


    B.
    A

    7.DTC CLEAR*
    1. Refer to the DTC Check/Clear (Click here).

      HINT:
      The current DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.

    NEXT

    8.RECHECK FOR DTC*
      Result 
      Result
      Proceed to
      DTC is output.
      A
      DTC is not output.
      B

      HINT:
      1. Even if the malfunction symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.
      2. If more information is needed, perform a recheck using the "System Check Mode" screen after rechecking for DTCs using the intelligent tester (Click here).
      3. Check the DTC and inspect the area code indicates.


    B.
    A

    9.DIAGNOSTIC TROUBLE CODE CHART
    1. Find the output code in Diagnostic Trouble Code Chart (Click here).

      NOTICE:
      1. The navigation system outputs DTCs for the following system.
      2. When DTCs other than those in Diagnostic Trouble Code Chart for the navigation system are output, refer to Diagnostic Trouble Code Chart for the system.
      3. Audio and visual system (w/ navigation system) (Click here)
      4. Parking assist monitor system (w/ parking assist monitor system) (Click here).

      Result 
      Result
      Proceed to
      DTCs for the navigation system are output.
      A
      DTCs for the audio and visual system (w/ navigation system) are output.
      B
      DTCs for the parking assist monitor system (w/ parking assist monitor system) are output.
      D


    A.

    B.

    D.
    10.CHECK HARD DISK DRIVE
    1. Hard Disk Drive in Operation Check (Click here).

      OK:
      "OK" is displayed.


    NG.
    OK

    11.PROBLEM SYMPTOMS TABLE
    1. Refer to Problem Symptoms Table (Click here).

      Result 
      Result
      Proceed to
      Fault is not listed in Problem Symptoms Table.
      A
      Fault is listed in Problem Symptoms Table.
      B

      HINT:
      If the symptom does not recur and no DTC is output, perform the symptom reproduction method (Click here).


    B.
    A

    12.CHECK ECU TERMINAL ARRANGEMENT BASED ON MALFUNCTION SYMPTOM
    1. Refer to Terminals of ECU (Click here).

    NEXT

    13.CHECK CIRCUIT
    1. Adjust, repair or replace as necessary.

    NEXT

    14.RECHECK FOR DIAGNOSTIC TROUBLE CODE

      HINT:
      After clearing the DTCs, recheck for DTCs.

    NEXT

    15.PERFORM CONFIRMATION TEST
      NEXT

      ← SYSTEM DESCRIPTION (Sep 2011 – Dec 2011)OPERATION CHECK (Sep 2011 – Dec 2011) →