Steering Pad Switch Circuit
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
This circuit sends an operation signal from the steering pad switch to the radio receiver.If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.
If there is a short in the circuit, the resulting condition is the same as if the switch were continuously depressed. Therefore, the audio system cannot be operated using the steering pad switch, and the audio system itself cannot function.
WIRING DIAGRAM


INSPECTION PROCEDURE
- CAUTION:
- The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution for the SRS (Click here).
| 1. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - SPIRAL CABLE) |
Disconnect the F19 receiver connector.
Disconnect the E12 cable connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F19-8 (SW2) - E12-5 (AU2)
Always
Below 1 Ω
F19-6 (SWG) - E12-4 (EAU)
F19-7 (SW1) - E12-6 (AU1)
F19-8 (SW2) - Body ground
Always
10 kΩ or higher
F19-6 (SWG) - Body ground
F19-7 (SW1) - Body ground
|
|
||||
| OK | |
| 2. INSPECT SPIRAL CABLE SUB-ASSEMBLY |


| *1 |
Vehicle Side |
*2 |
Steering Pad Switch Side |
Disconnect the z36 cable connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E12-4 (EAU) - z36-8 (EAU)
Spiral cable is turned 2.5 rotations counterclockwise
Below 1 Ω
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise
E12-5 (AU2) - z36-9 (AU2)
Spiral cable is turned 2.5 rotations counterclockwise
Below 1 Ω
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise
E12-6 (AU1) - z36-10 (AU1)
Spiral cable is turned 2.5 rotations counterclockwise
Below 1 Ω
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise
- CAUTION:
- The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the SRS (Click here).
|
|
||||
| OK | |
| 3. INSPECT STEERING PAD SWITCH ASSEMBLY |
Disconnect the z36 switch connector.


Text in Illustration *1
Volume+
*2
Volume-
*3
Seek-
*4
MODE
*5
Seek+
*6
Off Hook
*7
On Hook
-
-
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
10 (AU1) - 8 (EAU)
No switch is pushed
95 to 105 kΩ
Seek+ switch pushed
Below 2.5 Ω
Seek- switch pushed
312 to 345 Ω
Volume+ switch pushed
950 to 1050 Ω
Volume- switch pushed
2954 to 3265 Ω
9 (AU2) - 8 (EAU)
No switch is pushed
95 to 105 kΩ
MODE switch pushed
Below 2.5 Ω
On hook switch pushed
312 to 345 Ω
Off hook switch pushed
950 to 1050 Ω
Voice switch pushed
2954 to 3265 Ω
|
|
||||
| OK | ||
| ||
