2011-2013 Land Cruiser · Service Manual Steering

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering column (Click here).


1. FRONT WHEELS FACING STRAIGHT AHEAD

2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
  1. After the engine switch is turned off, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the engine switch off, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


4. REMOVE LOWER NO. 3 STEERING WHEEL COVER

  1. B181563
    Detach the 2 claws and remove the steering wheel cover.


5. REMOVE LOWER NO. 2 STEERING WHEEL COVER

  1. B189186E01
    Detach the 2 claws and remove the steering wheel cover.


6. REMOVE STEERING PAD (w/ Airbag System)

  1. B187261E01
    Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.

  1. B181568
    Pull out the steering pad from the steering wheel, as shown in the illustration. Then support the steering pad with one hand.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the horn connector.

  1. Disconnect the 2 connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


7. REMOVE STEERING PAD (w/o Airbag System)

HINT:
Refer to the step "REMOVE STEERING PAD (w/ Airbag System)".


8. REMOVE STEERING PAD SWITCH ASSEMBLY (w/ Steering Pad Switch)

  1. C172683
    Disconnect the connector.

  1. Remove the 2 screws.

  1. Detach the 4 claws and remove the steering pad switch.


9. REMOVE CRUISE CONTROL MAIN SWITCH (w/ Cruise Control System)

  1. B179759
    Disconnect the connector and clamp.

  1. B179760
    Remove the 2 screws.

  1. B179761
    Remove the switch.


10. REMOVE STEERING WHEEL ASSEMBLY
  1. Remove the steering wheel set nut.

  1. C172673E03
    Put matchmarks on the steering wheel and main shaft.
    Text in Illustration 
    *a
    Matchmark
    *b
    Hold
    *c
    Turn

  1. Using SST, remove the steering wheel assembly.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05011)


11. REMOVE STEERING WHEEL HEATER CONTROL ASSEMBLY (w/ Steering Heater)

  1. C259317
    Disconnect the 2 connectors.

  1. C259318
    Detach the connector clamp.

  1. Remove the 2 screws and steering wheel heater control assembly from the lower steering wheel boss cover.


12. REMOVE STEERING PAD COVER LH (w/o Steering Pad Switch)

  1. C246800E01
    Remove the screw and 3 guide pins, remove the steering pad cover.


13. REMOVE STEERING PAD COVER RH (w/o Steering Pad Switch)

HINT:
Use the same procedures described for the LH side.


14. REMOVE STEERING SHAKE DAMPER

  1. C246801
    Remove the 2 screws and remove the steering shake damper.


15. REMOVE STEERING WHEEL BOSS LOWER COVER

  1. C246491
    Remove the 2 screws and 4 claws, and remove the steering wheel boss lower cover.

← REMOVAL (Sep 2011 – Dec 2011)INSPECTION (Sep 2011 – Dec 2011) →