2011-2013 Land Cruiser · Service Manual Vehicle Interior

Theft Warning Siren Circuit

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The theft warning siren sounds if either of the following condition is met:
  1. The theft deterrent system is in the alarm sounding state.
  2. The theft warning siren is in the armed state when +B, GND or the communication line is open.

WIRING DIAGRAM

B311691E01

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the theft warning siren assembly, refer to the Service Bulletin.
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (THEFT WARNING SIREN)
  1. Operate the intelligent tester according to the steps on the display and select "Active Test".

    Entry&Start 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Horn2
    Theft warning siren
    ON / OFF
    -

    OK:
    Siren operates normally.



NG
Go to step 2
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

2. CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN - BATTERY AND BODY GROUND)

  1. B298276E04
    Disconnect the K46 theft warning siren assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    K46-5 (+B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K46-2 (GND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Theft Warning Siren Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - THEFT WARNING SIREN)
  1. Disconnect the E30 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the K46 theft warning siren assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E30-7 (SSCL) - K46-4 (CONT)
    Always
    Below 1 Ω
    E30-7 (SSCL) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK
    A
    NG (except Hood Courtesy Switch Connector 4 Pin Type)
    B
    NG (for Hood Courtesy Switch Connector 4 Pin Type)
    C



B
REPAIR OR REPLACE HARNESS OR CONNECTOR

C
Go to step 5
A


4. CHECK THEFT WARNING SIREN (OPERATION)
  1. Temporarily replace the theft warning siren assembly with a new or known good one (refer to the Service Bulletin).

  1. Check that the theft warning siren operates normally.

    OK:
    Operates normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (THEFT WARNING SIREN ASSEMBLY IS DEFECTIVE)

5. CHECK HARNESS AND CONNECTOR (HOOD LOCK ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY AND THEFT WARNING SIREN)
  1. Disconnect the E30 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the A8 hood lock assembly connector.

  1. Disconnect the K46 theft warning siren assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A8-1 (SLF+) - E30-7 (SSCL)
    Always
    Below 1 Ω
    A8-3 (SLF-) - K46-4 (CONT)
    Always
    Below 1 Ω
    A8-1 (SLF+) - Body ground
    Always
    10 kΩ or higher
    A8-3 (SLF-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HOOD LOCK ASSEMBLY (Click here)


← Theft Warning Siren Circuit (Sep 2011 – Dec 2011)Security Indicator Light Circuit (Sep 2011 – Dec 2011) →