2011-2013 Land Cruiser · Service Manual Vehicle Interior

Theft Warning Siren Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

  1. The theft warning siren (self power siren) has an internal battery. If the vehicle battery cable is disconnected or any of the communication lines are open, the theft warning siren (self power siren) detects this and sounds its siren.
  2. Although the theft warning siren (self power siren) usually sounds by receiving a signal from the certification ECU (smart key ECU assembly), the theft warning siren (self power siren) can sound by its internal battery in case the vehicle battery cable is disconnected.
  3. The certification ECU (smart key ECU assembly) sends an arming signal to the theft warning siren (self power siren) while transferring to the armed state, and it also sends a disarming signal to the siren while switching to the disarmed state. Also, the certification ECU (smart key ECU assembly) can cause the theft warning siren (self power siren) to sound by sending an alarm signal during the alarm sounding state.

WIRING DIAGRAM

B159044E03

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (THEFT WARNING SIREN [SELF POWER SIREN])
  1. Operate the intelligent tester according to the steps on the display and select "Active Test".

    Entry&Start 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Horn2
    Theft warning siren (self power siren)
    ON / OFF
    -

    OK:
    Siren operates normally.



NG
Go to step 2
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

2. CHECK THEFT WARNING SIREN (SELF POWER SIREN)
B192897E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    K18-1 (+B) - Body ground
    Always
    11 to 14 V
    K18-2 (GND) - Body ground
    Always
    Below 1 V
    K18-3 (CONT) - Body ground
    Switched from armed state or arming preparation state to disarmed state (1)
    Wave pattern (1) shown in chart below
    Switched from arming preparation state to armed state (2)
    Wave pattern (2) shown in chart below
    Normal condition (Except (1) and (2))
    1 to 2 V



NG
Go to step 3
OK

REPLACE THEFT WARNING SIREN (SELF POWER SIREN) (Click here)

3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - THEFT WARNING SIREN [SELF POWER SIREN])
B160032E02
  1. Disconnect the E30 ECU connector.

  1. Disconnect the K18 siren connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E30-7 (SSCL) - K18-3 (CONT)
    Always
    Below 1 Ω
    E30-7 (SSCL) or K18-3 (CONT) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN [SELF POWER SIREN] - BODY GROUND)
B108843E06
  1. Disconnect the K18 siren connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K18-2 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


← Intrusion Sensor Cancel Switch Circuit (from Sep 2011)Theft Warning Siren Circuit (from Jan 2012) →