2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL WATER PUMP ASSEMBLY

  1. A174307
    Install a new gasket and the water pump with the 17 bolts.

    Torque:
    for 10 mm head:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
    for 12 mm head:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }


2. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

  1. A175285E01
    Temporarily install the V-ribbed belt tensioner with the 5 bolts.

  1. Tighten bolt 1 and 2 in numerical order.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Tighten the other bolts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

    Standard Bolt:
    Item
    Length
    A
    70 mm (2.76 in.)
    B
    33 mm (1.30 in.)


3. CONNECT COOLER COMPRESSOR ASSEMBLY
  1. Fix the cooler compressor in place with the stud bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. A174385E01
    Install the cooler compressor with the nut and 3 bolts in several steps in the sequence shown in the illustration.

    Torque:
    24 N*m{ 250 kgf*cm , 18 ft.*lbf }

  1. Connect the cooler compressor connector.


4. INSTALL GENERATOR ASSEMBLY

  1. A177920
    Install the generator with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. A177921
    Connect the wire harness clamp bracket with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the wire harness clamp to the bracket.

  1. Connect the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.

  1. Connect the generator connector.

  1. A180582
    Connect the wire harness clamp bracket with the nut.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


5. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

A238835E01

  1. w/ Pulley Cover Plate:

    1. A191314E01
      Install the idler pulley cover plate, idler pulley and No. 2 idler pulley cover plate with the bolt.

      Torque:
      54 N*m{ 551 kgf*cm , 40 ft.*lbf }

      NOTICE:
      If it is necessary to replace the pulley or either plate, replace the No. 2 idler pulley cover plate, No. 2 idler pulley and idler pulley cover plate as a set with new parts.

  1. w/o Pulley Cover Plate:
    Install the 2 No. 2 idler pulleys with the 2 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }


6. INSTALL WATER INLET HOUSING

A174308E01
  1. Install a new gasket to the water outlet pipe.

  1. Install a new gasket to the water pump.

  1. Apply soapy water to the gasket of the water outlet pipe.

  1. A174305
    Install the water inlet with the 5 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. A243260
    Connect the 5 water by-pass hoses.

  1. A174303
    Connect the 2 oil cooler hoses.


7. INSTALL FAN SHROUD
  1. Install the fan pulley to the water pump.

  1. Place the shroud together with the coupling fan between the radiator and engine.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Temporarily install the fluid coupling fan to the water pump with the 4 nuts. Tighten the nuts as much as possible by hand.

  1. A174325
    Attach the claws of the shroud to the radiator as shown in the illustration.

  1. Install the shroud with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the reservoir hose to upper side of the radiator tank upper.

  1. Install the fan and generator V-belt (Click here).

  1. Tighten the 4 nuts of the fluid coupling fan.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


8. CONNECT OIL COOLER TUBE (w/ Air Cooled Transmission Oil Cooler)

  1. A184406
    Connect the oil cooler tube with the 2 bolts, and attach the claw to close the flexible hose clamp.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


9. INSTALL NO. 2 RADIATOR HOSE

  1. A174327
    Install the radiator hose.


10. INSTALL NO. 1 RADIATOR HOSE

  1. A174326
    Install the radiator hose.


11. INSTALL AIR CLEANER ASSEMBLY

  1. A151811E02
    Install the air cleaner assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Tighten the hose clamp.

    HINT:
    Tighten the hose clamp until it reaches the specified protrusion height labeled A shown in the illustration.

    Standard protrusion height:
    Less than 0.5 mm (0.0197 in.)

  1. A185261
    Connect the MAF meter connector.

  1. Attach the 2 wire harness clamps.

  1. Connect the vacuum hose.

  1. A151812
    Attach the hose clamp.

  1. Connect the No. 2 ventilation hose.


12. INSTALL NO. 2 AIR CLEANER HOSE

  1. A184327E01
    Align the protrusion of the pre-cleaner with the groove of the No. 2 air cleaner hose as shown in the illustration.

  1. A178933E01
    Tighten the 2 hose clamps.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    HINT:
    Tighten the clamp until the end of the clamp band is within both limit marks.


13. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard Capacity:
    Item
    Specified condition
    for Automatic transmission
    w/o Rear Heater
    11.2 liters (11.8 US qts, 9.9 Imp. qts)
    w/ Rear Heater
    14.4 liters (15.2 US qts, 12.7 Imp. qts)
    for Manual transmission
    w/o Rear Heater
    12.0 liters (12.7 US qts, 10.6 Imp. qts)
    w/ Rear Heater
    14.6 liters (15.4 US qts, 12.8 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. A174295E01
    Slowly pour coolant into the radiator reservoir until it reaches the F line.

  1. Install the reservoir cap.

  1. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Set the air conditioning as follows while warming up the engine.

    Item
    Condition
    Fan speed
    Any setting except off
    Temperature
    Toward WARM
    Air conditioning switch
    Off

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the F line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves. Heat areas on the parts may injure your hands.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A174297E01
    Check that the coolant level is between the F and L lines.
    If the coolant level is below the L line, repeat all of the procedures above.
    If the coolant level is above the F line, drain coolant so that the coolant level is between the F and L lines.


14. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A174294
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.


15. INSTALL UPPER RADIATOR SUPPORT SEAL

  1. B180889
    Install the radiator support seal with the 7 clips.


16. INSTALL V-BANK COVER

  1. A174359
    Install the V-bank cover with the 2 cap nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


17. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Install the under cover with the 10 bolts.


18. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


19. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the fender splash shield.

← REMOVAL (from Jan 2012)INSTALLATION (from Jan 2012) →