2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0335 Crankshaft Position Sensor "A" Circuit

Diagnostic trouble codes · Vehicles built from Jan 2012

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and magnet. The sensor plate rotates, and a pulse signal is created as each tooth passes by the pickup coil. The pickup coil generates 34 signals for each revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the common rail injection system is controlled.
P0335 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Crank or start engine
When one of the following conditions is met (for 5 seconds during cranking or 0.5 seconds during engine start) (1 trip detection logic):
  1. No crankshaft position sensor signal is sent to the ECM while cranking.
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. No. 1 crankshaft position sensor plate (crankshaft)
  4. ECM
P0339 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Engine running at 1000 rpm or more with vehicle stationary
No crankshaft position sensor signal is input to the ECM for 0.05 seconds or more, and conditions (a), (b) and (c) are met (1 trip detection logic):
  1. (a) Engine speed is 1000 rpm or more.
  2. (b) STA signal is off.
  3. (c) 3 seconds or more have elapsed after STA signal is switched from on to off.
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. No. 1 crankshaft position sensor plate (crankshaft)
  4. ECM
Related Data List 
DTC No.
Data List
P0335
Engine Speed
P0339

HINT:
  1. If DTC P0335 and/or P0339 is stored, the following symptoms may appear:
    1. Difficult starting
    2. Misfire
    3. Combustion noise
    4. Black smoke
    5. White smoke
    6. Lack of power


WIRING DIAGRAM

A165739E03

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
  2. The Data List item Engine Speed is calculated from the output of the crankshaft position sensor.
  3. A DTC is also stored when the ground of a shielded wire is faulty.


1. INSPECT CRANKSHAFT POSITION SENSOR

  1. A165740E01
    Disconnect the crankshaft position sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (NE+) - 2 (NE-)
    Cold
    1630 to 2740 Ω
    1 (NE+) - 2 (NE-)
    Hot
    2065 to 3225 Ω

    HINT:
    In the table above, the terms "Cold" and "Hot" refer to the temperature of the coils in the sensor. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).



NG
Go to step 6
OK


2. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

  1. A182475E01
    Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C65-1 (NE+) - C45-78 (NE+)
    Always
    Below 1 Ω
    C65-2 (NE-) - C45-77 (NE-)
    Always
    Below 1 Ω
    C65-3 - Body ground
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C65-1 (NE+) - C46-78 (NE+)
    Always
    Below 1 Ω
    C65-2 (NE-) - C46-77 (NE-)
    Always
    Below 1 Ω
    C65-3 - Body ground
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C65-1 (NE+) or C45-78 (NE+) - Body ground
    Always
    10 kΩ or higher
    C65-2 (NE-) or C45-77 (NE-) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C65-1 (NE+) or C46-78 (NE+) - Body ground
    Always
    10 kΩ or higher
    C65-2 (NE-) or C46-77 (NE-) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 7
OK


3. CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)

  1. BR03795E15
    Check the sensor installation.

    OK:
    Sensor is installed correctly.



NG
Go to step 8
OK


4. CHECK NO. 1 CRANKSHAFT POSITION SENSOR PLATE
  1. Check the teeth of the sensor plate.

    OK:
    The sensor plate teeth do not have any cracks or deformation.



NG
Go to step 9
OK


5. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 10
6. REPLACE CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).



NEXT
Go to step 10
7. REPAIR OR REPLACE HARNESS OR CONNECTOR


NEXT
Go to step 10
8. SECURELY REINSTALL SENSOR
  1. Securely reinstall sensor (Click here).



NEXT
Go to step 10
9. REPLACE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
  1. Replace the No. 1 crankshaft position sensor plate (Click here).


NEXT


10. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine and run it at 1000 rpm or more.

  1. Confirm that the DTC is not output again.

    HINT:
    Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.

    1. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

    2. Input DTC P0335 and/or P0339.

    3. Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, after increasing the engine speed to 1000 rpm for approximately 1 second, idle the engine for 5 minutes.


NEXT

END


← P0335 Crankshaft Position Sensor "A" Circuit (+ P0339) (Sep 2011 – Dec 2011)P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) (Sep 2011 – Dec 2011) →