2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

DISASSEMBLY

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

CAUTION:
When replacing an injector (including interchanging injectors between cylinders), common rail, cylinder head, or intake manifold, replace the corresponding injection pipes with a new one.


1. REMOVE CAMSHAFT POSITION SENSOR

A163142
  1. Disconnect the sensor connector.

  1. Remove the bolt and sensor.


2. REMOVE CRANKSHAFT POSITION SENSOR

A175725
  1. Disconnect the sensor wire harness clamp.

  1. Remove the bolt and sensor.


3. DISCONNECT NO. 1 OIL COOLER HOSE

A170325E01
Text in Illustration 
*1
No. 1 Oil Cooler Hose
*2
No. 2 Oil Cooler Hose

4. DISCONNECT NO. 2 OIL COOLER HOSE

5. REMOVE CRANKSHAFT PULLEY

NOTICE:
A181685E02
This procedure is intended for removal/installation of the crankshaft pulley only. Do not use this procedure for removal/installation of the flywheel or the drive plate and ring gear.

Text in Illustration 
*1
Service Hole
*2
Protrusion
  1. Install the 2 bolts to the bolt holes of the crankshaft rear side.

  1. Using a bar, turn the crankshaft until the crankshaft pulley service hole is a little to the left of bottom dead center.

  1. Install a 14 mm x 1.5 pitch service bolt with a length of 70 mm or more to the crankshaft pulley service hole, and hold the crankshaft using the timing chain cover protrusion.

  1. Remove the 3 bolts and crankshaft pulley.

    NOTICE:
    If the crankshaft pulley cannot be removed, temporarily install a bolt to the crankshaft so that the pulley does not fall, and lightly tap the outer edge of the mass damper with a plastic-faced hammer to remove the pulley. Do not tap the pulley V-ribbed belt ribs, as the crankshaft may be damaged.


6. REMOVE TIMING GEAR COVER SPACER (w/ Intercooler)

  1. A177415
    Remove the 2 bolts and timing gear cover spacer.


7. REMOVE OIL FILTER CAP WITH ELEMENT

  1. A174852
    Remove the oil filter drain plug.

  1. A094910E04
    Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

  1. Remove the O-ring from the oil filter drain plug and install it to the drain pipe.

  1. A174853E01
    Install the oil filter drain pipe to the oil filter cap and drain the engine oil.

  1. Remove the oil filter drain pipe.

  1. Apply a light coat of engine oil to a new O-ring, and install it to the oil filter drain plug.

  1. A174852
    Install the oil filter drain plug to the oil filter cap.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. A174854E01
    Using SST, remove the oil filter cap.
    SST
    09228-06501  

    HINT:
    Use a container to catch the draining oil. After the oil filter cap is loosened approximately 4 turns and the cap ribs are vertical, engine oil drains from the gap between the oil filter cap and oil pan.

  1. A106167E05
    Remove the oil filter element and O-ring from the oil filter cap.

    NOTICE:
    Be sure to remove the cap O-ring by hand, without using any tools, to prevent damage to the cap O-ring groove.


8. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

  1. A170281
    Disconnect the oil pressure sender gauge connector.

  1. Remove the oil pressure sender gauge.


9. REMOVE OIL COOLER ASSEMBLY

  1. A170278
    Remove the 2 bolts, 2 nuts and oil cooler.

  1. A170279
    Remove the 2 O-rings and oil cooler gasket.


10. REMOVE OIL COOLER RELIEF VALVE ASSEMBLY

  1. A177211
    Remove the oil cooler relief valve and gasket.


11. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

  1. A177213
    Remove the 3 bolts, 2 nuts and oil filter bracket.

  1. A177439
    Remove the 2 O-rings.


12. REMOVE ENGINE OIL LEVEL SENSOR

  1. A174870
    Remove the 4 bolts and engine oil level sensor.

  1. Remove the gasket.


13. REMOVE OIL PAN DRAIN PLUG

  1. A177219
    Remove the oil pan drain plug and gasket.


14. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

  1. A174871
    Remove the 10 bolts and 2 nuts.

  1. A174872
    Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.

    NOTICE:
    Be careful not to damage the contact surfaces of the No. 1 and No. 2 oil pans.


15. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A174873
    Remove the 2 bolts and oil strainer.

  1. Remove the O-ring from the oil strainer.


16. REMOVE NO. 1 OIL PAN SUB-ASSEMBLY

  1. A174874E02
    Remove the 20 bolts, 2 nuts and oil reflector plate.

    NOTICE:
    If the oil reflector plate is deformed, replace it.

    HINT:
    Be sure to clean the bolts and stud bolts, and check the threads for cracks or other damage.

  1. A177413
    Remove the No. 1 oil pan by prying between the No. 1 oil pan and cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

    HINT:
    Tape the screwdriver tip before use.

  1. A174876
    Remove the 3 O-rings.

  1. A179094
    Remove the cylinder block oil hole gasket.


17. REMOVE NO. 1 OIL PAN BAFFLE PLATE

  1. A177220
    Remove the 5 bolts and No. 1 oil pan baffle plate.


18. REMOVE INLET OIL PUMP PIPE

  1. A177221
    Remove the 3 bolts and inlet oil pump pipe.

  1. Remove the O-ring from the inlet oil pump pipe.


19. REMOVE OIL REGULATOR ASSEMBLY

  1. A161977
    Remove the 4 bolts and oil regulator.


20. REMOVE REAR ENGINE OIL SEAL RETAINER

  1. A161974
    Remove the 10 bolts.

  1. Remove the oil seal retainer by prying between the oil seal retainer and cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.


21. REMOVE REAR CRANKSHAFT OIL SEAL

  1. A164590
    Place the oil seal retainer on wooden blocks.

  1. Using a screwdriver and hammer, tap out the oil seal.

    HINT:
    Tape the screwdriver tip before use.


22. REMOVE OIL PUMP ASSEMBLY

  1. A161979
    Remove the 4 bolts and oil pump.


23. REMOVE SCAVENGING PUMP ASSEMBLY

  1. A161978
    Remove the 4 bolts and scavenging pump.


24. REMOVE OIL FILLER CAP SUB-ASSEMBLY

A164467

25. REMOVE OIL FILLER CAP GASKET

26. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH (w/o DPF)

  1. A174971
    Remove the 18 bolts, cylinder head cover and gasket.


27. REMOVE NOZZLE HOLDER GASKET RH (w/o DPF)

  1. A174977
    Using a small screwdriver and hammer, remove the 4 nozzle holder gaskets.

    HINT:
    Tape the screwdriver tip before use.


28. REMOVE NOZZLE HOLDER SEAL RH (w/o DPF)

  1. A164171
    Using a small screwdriver, remove the 4 holder seals by prying the portion between each holder seal and the cutout part of the cylinder head cover.

    HINT:
    Tape the screwdriver tip before use.


29. REMOVE CYLINDER HEAD COVER INSULATOR RH (w/ DPF)

30. REMOVE FUEL INJECTOR RH (w/ DPF)

  1. A271220
    Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 injectors.

    HINT:
    Arrange the injectors, holder clamps, washers and bolts in the correct order.

  1. Remove the O-ring from each injector.

  1. Remove the 4 injection nozzle seats from the cylinder head.


31. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH (w/ DPF)

  1. A267294
    Remove the 19 bolts, 4 nozzle holder clamp seats and cylinder head cover RH.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nozzle Holder Clamp Seat

  1. Remove the cylinder head cover gasket RH and No. 3 cylinder head cover gasket from the cylinder head cover RH.


32. REMOVE NO. 2 FUEL PUMP BRACKET (w/ DPF)

  1. A267293
    Remove the bolt and No. 2 fuel pump bracket.


33. REMOVE CYLINDER HEAD COVER INSULATOR LH (w/ DPF)

34. REMOVE FUEL INJECTOR LH (w/ DPF)

  1. A271221
    Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 injectors.

    HINT:
    Arrange the injectors, holder clamps, washers and bolts in the correct order.

  1. Remove the O-ring from each injector.

  1. Remove the 4 injection nozzle seats from the cylinder head.


35. REMOVE OIL SEPARATOR ASSEMBLY

  1. A164169
    Remove the 3 bolts, oil separator and gasket.


36. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH (w/ DPF)

  1. A267296
    Remove the 18 bolts, 4 nozzle holder clamp seats and cylinder head cover LH.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nozzle Holder Clamp Seat

  1. Remove the cylinder head cover gasket LH and No. 4 cylinder head cover gasket from the cylinder head cover LH.


37. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH (w/o DPF)

  1. A164162
    Remove the 17 bolts, cylinder head cover and gasket.


38. REMOVE NOZZLE HOLDER GASKET LH (w/o DPF)

  1. A174977
    Using a small screwdriver and hammer, remove the 4 nozzle holder gaskets.

    HINT:
    Tape the screwdriver tip before use.


39. REMOVE NOZZLE HOLDER SEAL LH (w/o DPF)

  1. A164170
    Using a small screwdriver, remove the 4 holder seals by prying the portion between each holder seal and the cutout part of the cylinder head cover.

    HINT:
    Tape the screwdriver tip before use.


40. REMOVE FUEL INJECTOR RH (w/o DPF)

  1. A176409
    Remove the union bolt, 4 hollow screws, 5 gaskets and nozzle leakage pipe.
    Text in Illustration 
    V100136
    Union Bolt

    NOTICE:
    1. When removing the nozzle leakage pipe, place a cushion under the pipe.
    2. Be careful not to deform or scratch the union seal surface.
    3. After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. A164166
    Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 injectors.

    HINT:
    Arrange the injectors, holder clamps, washers and bolts in the correct order.

  1. Remove the O-ring from each injector.

  1. Remove the 4 injection nozzle seats from the cylinder head.


41. REMOVE FUEL INJECTOR LH (w/o DPF)

  1. A176410
    Remove the union bolt, 4 hollow screws, 5 gaskets and No. 2 nozzle leakage pipe.
    Text in Illustration 
    V100136
    Union Bolt

    NOTICE:
    1. When removing the nozzle leakage pipe, place a cushion under the pipe.
    2. Be careful not to deform or scratch the union seal surface.
    3. After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. A164165
    Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 injectors.

    HINT:
    Arrange the injectors, holder clamps, washers and bolts in the correct order.

  1. Remove the O-ring from each injector.

  1. Remove the 4 injection nozzle seats from the cylinder head.


42. REMOVE WATER PUMP ASSEMBLY

  1. A174821
    Remove the 9 bolts, 2 nuts, water pump and gasket.


43. REMOVE TIMING CHAIN COVER PLATE

A174824
  1. Remove the 4 bolts, cover plate and gasket.


44. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A164495E02
    Remove the 4 nuts and 16 bolts.
    Text in Illustration 
    *1
    Nut

  1. Using a screwdriver, remove the timing chain cover by prying between the timing chain cover and timing gear case.

    HINT:
    A164496
    Tape the screwdriver tip before use.

  1. A174785
    Remove the O-ring from the timing gear case.


45. REMOVE FRONT CRANKSHAFT OIL SEAL

  1. A158677E02
    Place the timing chain cover on wooden blocks.
    Text in Illustration 
    *1
    Wooden Block

  1. Using a screwdriver and wooden block, pry out the oil seal.

    NOTICE:
    Do not damage the surface of the oil seal press fit hole.

    HINT:
    Tape the screwdriver tip before use.


46. SET NO. 1 CYLINDER TO TDC/COMPRESSION
  1. Temporarily install the 2 crankshaft pulley set bolts to the crankshaft.

  1. Turn the crankshaft clockwise to set the No. 1 cylinder to TDC.

  1. With the crankshaft key 45° counterclockwise from the top position, check that the timing marks of the RH and LH camshaft timing gears are aligned. If not as specified, turn the crankshaft 1 revolution (360°) and align the timing marks as shown below.

    A174764E02

    Text in Illustration 
    *1
    Key
    -
    -
    *a
    Top
    -
    -

  1. Remove the 2 crankshaft pulley set bolts.


47. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

  1. A174765
    Using a T30 "TORX" wrench, remove the 2 screws and crankshaft position sensor plate.


48. REMOVE PUMP DRIVE SHAFT GEAR

  1. A164498E01
    Using SST, hold the pump drive shaft gear.
    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 4 bolts and pump drive shaft gear.


49. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
  1. Push the tensioner slipper away from the tensioner, and move the stopper plate clockwise to release the lock as shown in A.

  1. Push down the tensioner slipper and move the stopper plate counterclockwise to set the lock as shown in B.

  1. Push the tensioner slipper away from the tensioner, and insert a hexagon wrench into the stopper plate hole as shown in C.

    A177339E02

    Text in Illustration 
    *1
    Stopper Plate
    -
    -

  1. A174766
    Remove the 2 bolts and No. 1 chain tensioner.


50. REMOVE NO. 1 CHAIN TENSIONER SLIPPER

A174767

51. REMOVE NO. 1 CHAIN VIBRATION DAMPER

  1. A164501
    Remove the 2 bolts and No. 1 chain vibration damper.


52. REMOVE NO. 1 CAMSHAFT TIMING SPROCKET AND NO. 1 TIMING CHAIN

A181663

53. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY
  1. Push the tensioner slipper away from the tensioner, and move the stopper plate clockwise to release the lock as shown in A.

  1. Push up the tensioner slipper and move the stopper plate counterclockwise to set the lock as shown in B.

  1. Push the tensioner slipper away from the tensioner, and insert a hexagon wrench into the stopper plate hole as shown in C.

    A177342E02

    Text in Illustration 
    *1
    Stopper Plate
    -
    -

  1. A164503
    Remove the 2 bolts and No. 2 chain tensioner.


54. REMOVE NO. 2 CHAIN TENSIONER SLIPPER

A164504

55. REMOVE NO. 2 CHAIN VIBRATION DAMPER

  1. A180675
    Remove the 2 bolts and No. 2 chain vibration damper.


56. REMOVE NO. 2 CAMSHAFT TIMING SPROCKET AND NO. 2 TIMING CHAIN

  1. A164506E01
    Using SST, hold the No. 2 camshaft timing sprocket.
    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 4 bolts, No. 2 camshaft timing sprocket and No. 2 timing chain.


57. REMOVE FUEL SUPPLY PUMP DRIVE GEAR NUT
  1. Using SST, hold the idle gear.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the nut.

    A257020E02

    Text in Illustration 
    *A
    w/ Intercooler
    *B
    w/o Intercooler


58. REMOVE IDLE GEAR ASSEMBLY

  1. A180280
    w/ Intercooler:
    Using an 8 mm x 1.25 pitch service bolt with a length of 15 mm or more, fix the idle gear in place.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. A257018E02
    Remove the 2 bolts, idle gear thrust plate and idle gear.
    Text in Illustration 
    *A
    w/ Intercooler
    *B
    w/o Intercooler


59. SEPARATE SUB IDLE GEAR, IDLE GEAR SPRING AND IDLE GEAR (w/ Intercooler)

  1. A177419
    Hold the idle gear in a vise between aluminum plates.

    NOTICE:
    Be careful not to damage the gears.

  1. A177420E01
    Using SST, hole the idle gear, and remove the bolt and sub idle gear.
    SST
    09960-10010   (09962-01000, 09963-00700)

  1. A177421
    Remove the idle gear spring from the idle gear.


60. REMOVE NO. 1 IDLE GEAR SHAFT

A164511

61. REMOVE FUEL SUPPLY PUMP DRIVE GEAR

  1. A164509E01
    Using SST, remove the fuel supply pump drive gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031)


62. INSPECT RADIAL BALL BEARING

  1. A164845
    Turn the bearing, and check that the bearing moves smoothly and quietly.
    If it moves roughly or noisily, replace the radial ball bearing.


63. REMOVE RADIAL BALL BEARING

A158678E01

HINT:
It is not necessary to remove the bearing unless it is being replaced.

  1. Using SST, remove the radial ball bearing.

    SST
    09950-00020  
    09950-00030  
    09950-60010   (09951-00580)
    09950-40011   (09957-04010)


64. SEPARATE FUEL SUPPLY PUMP DRIVE GEAR AND FUEL SUPPLY PUMP SHAFT SPROCKET

  1. A158679
    Hold the fuel supply pump shaft sprocket in a vise between aluminum plates.

    NOTICE:
    Be careful not to damage the gears.

  1. Remove the 4 bolts and separate the fuel supply pump drive gear and fuel supply pump shaft sprocket.


65. REMOVE STRAIGHT PIN

HINT:
A158649
It is not necessary to remove the straight pin unless it is being replaced.

  1. Remove the straight pin.


66. REMOVE FUEL SUPPLY PUMP ASSEMBLY

  1. A158684
    Using a 6 mm hexagon wrench, remove the hexagon bolt. Then remove the 2 nuts and fuel supply pump.

  1. Remove the O-ring.


67. REMOVE V-BANK SILENCER

A164488

68. REMOVE TIMING GEAR CASE SUB-ASSEMBLY

  1. A164875E02
    Remove the 22 bolts, 2 nuts and timing gear case shown in the illustration.
    Text in Illustration 
    *1
    Nut

  1. A177346
    Remove the 2 O-rings and timing gear case gasket.


69. DISCONNECT NO. 2 VACUUM TRANSMITTING HOSE (w/ Intercooler)

A177331

70. DISCONNECT NO. 3 VACUUM TRANSMITTING HOSE (w/ Intercooler)

A177332

71. REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ Intercooler)

  1. A177333
    Remove the 2 bolts and No. 1 vacuum transmitting pipe.


72. REMOVE NO. 2 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ Intercooler)

  1. A177334
    Remove the 3 bolts and No. 2 vacuum transmitting pipe.


73. REMOVE NO. 2 TIMING GEAR CASE INSULATOR (w/ Intercooler)

A177335

74. REMOVE NO. 1 AND NO. 2 CAMSHAFTS

  1. A164905
    Using a 6 mm x 1.0 pitch service bolt with a length of 16 mm or more, fix the No. 1 camshaft in place.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. A164787
    Loosen the 2 union bolts.

  1. A164788E01
    Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.

  1. A164789
    Remove the 2 union bolts and No. 1 and No. 2 oil feed pipes.

  1. A164790
    Remove the 8 No. 3 camshaft bearing caps and No. 1 camshaft bearing cap.

    HINT:
    Be sure to arrange the removed parts for each installation position separately.

  1. A164529
    Remove the No. 1 and No. 2 camshafts.


75. REMOVE NO. 2 CAMSHAFT BEARING CAP

A164530

76. REMOVE NO. 1 VALVE ROCKER ARM

  1. A164531
    Remove the 16 No. 1 valve rocker arms.

    HINT:
    Be sure to arrange the removed parts for each installation position separately.


77. REMOVE NO. 1 VALVE LASH ADJUSTER ASSEMBLY

  1. A164532
    Remove the 16 No. 1 valve lash adjusters.

    HINT:
    Be sure to arrange the removed parts for each installation position separately.


78. REMOVE CYLINDER HEAD SUB-ASSEMBLY RH

  1. A164533E01
    Uniformly loosen and remove the 10 bolts and 10 spacers in the sequence shown in the illustration. Then remove the cylinder head.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Be sure to arrange the removed parts for each installation position separately.


79. REMOVE NO. 1 CYLINDER HEAD GASKET

80. REMOVE NO. 3 AND NO. 4 CAMSHAFTS

  1. A164905
    Using a 6 mm x 1.0 pitch service bolt with a length of 16 mm or more, fix the No. 4 camshaft in place.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. A164783
    Loosen the 2 union bolts.

  1. A164784E01
    Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.

  1. A164785
    Remove the 2 union bolts and No. 3 and No. 4 oil feed pipes.

  1. A164786
    Remove the 8 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap.

    HINT:
    Be sure to arrange the removed parts for each installation position separately.

  1. A164537
    Remove the No. 3 and No. 4 camshafts.


81. REMOVE NO. 5 CAMSHAFT BEARING CAP

A164538

82. REMOVE NO. 2 VALVE ROCKER ARM

  1. A164539
    Remove the 16 No. 2 valve rocker arms.

    HINT:
    Be sure to arrange the removed parts for each installation position separately.


83. REMOVE NO. 2 VALVE LASH ADJUSTER ASSEMBLY

  1. A164540
    Remove the 16 No. 2 valve lash adjusters.

    HINT:
    Be sure to arrange the removed parts for each installation position separately.


84. REMOVE CYLINDER HEAD SUB-ASSEMBLY LH

  1. A164541E01
    Uniformly loosen and remove the 10 bolts and 10 spacers in the sequence shown in the illustration. Then remove the cylinder head.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Be sure to arrange the removed parts for each installation position separately.


85. REMOVE NO. 2 CYLINDER HEAD GASKET

86. REPLACE STUD BOLT

HINT:
A177310E02
If the stud bolt is deformed or the threads are damaged, replace it.

  1. Intake Pipe:

    1. Using an E8 "TORX" wrench, replace the 4 stud bolts.

      Torque:
      6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. No. 3 Intake Manifold:

    1. A177311E02
      Using an E8 "TORX" wrench, replace the 2 stud bolts labeled A.

      Torque:
      6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    2. Using an E6 "TORX" wrench, replace the 2 stud bolts labeled B.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    3. Using an E6 "TORX" wrench, replace the stud bolt labeled C.

      Torque:
      4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Oil Filter Bracket:

    1. A177312E02
      Using an E8 "TORX" wrench, replace the 2 stud bolts.

      Torque:
      6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. No. 1 Oil Pan:

    1. A177313E02
      Using an E8 "TORX" wrench, replace the 2 stud bolts labeled A.

      Torque:
      6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    2. Using an E7 "TORX" wrench, replace the 2 stud bolts labeled B.

      Torque:
      5.2 N*m{ 53 kgf*cm , 46 in.*lbf }

  1. Timing Chain Cover:

    1. A177314E01
      Using an E7 "TORX" wrench, replace the 2 stud bolts labeled A.

      Torque:
      6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    2. Replace the 2 stud bolts labeled B.

      Torque:
      12 N*m{ 120 kgf*cm , 9 ft.*lbf }

  1. Timing Gear Case:

    1. A180682E01
      Using an E7 "TORX" wrench, replace the 4 stud bolts.

      Torque:
      6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    2. A180683E01
      Remove the 2 stud bolts.

    3. Remove the adhesive from the threads of the timing gear case.

    4. Apply adhesive to 2 or more threads of the 2 stud bolts.

    5. Install the 2 stud bolts.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }


87. REPLACE STRAIGHT SCREW PLUG

HINT:
A177222
If water or oil leaks from the straight screw plug or the plug is corroded, replace it.

  1. No. 1 Oil Pan:

    1. Using a 10 mm hexagon wrench, replace the straight screw plug and/or gasket.

      Torque:
      50 N*m{ 510 kgf*cm , 37 ft.*lbf }

    2. A177223
      Using a 14 mm hexagon wrench, replace the straight screw plug and/or gasket.

      Torque:
      86 N*m{ 877 kgf*cm , 63 ft.*lbf }

  1. Oil Filter Bracket:

    1. A177214
      Using a 10 mm hexagon wrench, replace the straight screw plug and/or gasket.

      Torque:
      50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Timing Gear Case:

    1. A177320
      Using a 10 mm hexagon wrench, replace the straight screw plug and/or gasket.

      Torque:
      40 N*m{ 408 kgf*cm , 30 ft.*lbf }


88. REPLACE CYLINDER BLOCK STRAIGHT SCREW PLUG

HINT:
If water leaks from the straight screw plug or the plug is corroded, replace it.

  1. A177329
    Replace the 2 straight screw plugs and 2 gaskets.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

    Text in Illustration 
    V100136
    Front


89. REPLACE RING PIN

HINT:
It is not necessary to remove the ring pin unless it is being replaced.

  1. No. 1 and No. 2 Intake Manifold:

    1. A177321E02
      Replace the ring pin.

      Standard protrusion:
      4.4 to 5.6 mm (0.173 to 0.222 in.)

      Text in Illustration 
      *a
      4.4 to 5.6 mm

  1. Cylinder Head:

    1. A177322E02
      Replace the ring pin.

      Standard protrusion:
      4.4 to 5.6 mm (0.173 to 0.222 in.)

      Text in Illustration 
      *a
      RH
      *b
      LH
      *c
      4.4 to 5.6 mm

  1. V-ribbed Belt Tensioner:

    1. A177316E02
      Replace the ring pin.

      Standard protrusion:
      4.7 to 5.7 mm (0.185 to 0.224 in.)

      Text in Illustration 
      *a
      4.7 to 5.7 mm

  1. Timing Chain Case:

    1. A177317E02
      Replace the ring pin.

      Standard protrusion:
      4.7 to 5.7 mm (0.185 to 0.224 in.)

      Text in Illustration 
      *a
      4.7 to 5.7 mm

  1. Timing Gear Case:

    1. A177315E04
      Replace the ring pin.

      Standard protrusion:
      5.2 to 5.7 mm (0.205 to 0.224 in.)

      Text in Illustration 
      *a
      5.2 to 5.7 mm

  1. Cylinder Head RH:

    1. A164903E03
      Replace the ring pin.

      Standard protrusion:
      2.5 to 3.5 mm (0.0984 to 0.138 in.)

      Text in Illustration 
      *a
      No. 2 Camshaft Bearing Cap
      *b
      Cylinder Head RH
      *c
      2.5 to 3.5 mm

  1. Cylinder Head LH:

    1. A164903E04
      Replace the ring pin.

      Standard protrusion:
      2.5 to 3.5 mm (0.0984 to 0.138 in.)

      Text in Illustration 
      *a
      No. 5 Camshaft Bearing Cap
      *b
      Cylinder Head LH
      *c
      2.5 to 3.5 mm


90. REPLACE CHAIN TENSIONER STRAIGHT PIN

HINT:
It is not necessary to remove the straight pin unless it is being replaced.

  1. A177318E02
    Replace the straight pin.

    Standard protrusion:
    18 to 20 mm (0.709 to 0.787 in.)

    Text in Illustration 
    *a
    18 to 20 mm


91. REPLACE TIMING GEAR COVER SET STRAIGHT PIN

HINT:
It is not necessary to remove the straight pin unless it is being replaced.

  1. A177319E02
    Replace the straight pin.

    Standard protrusion:
    5.0 to 7.5 mm (0.197 to 0.295 in.)

    Text in Illustration 
    *a
    5.0 to 7.5 mm


92. REPLACE HOLE PLUG (w/o Intercooler)

HINT:
It is not necessary to remove a hole plug unless it is being replaced.

  1. Remove the hole plug from the No. 4 camshaft.

  1. A257024E02
    Using a 12 mm steel bar and hammer, tap in the hole plug as shown in the illustration.
    Text in Illustration 
    *1
    No. 4 Camshaft
    *2
    Hole Plug


93. REPLACE TIGHT PLUG (w/o Intercooler)

NOTICE:
If oil leaks from a tight plug or a plug is corroded, replace it.

  1. Remove the tight plug from the timing chain cover.

  1. Apply adhesive to a new tight plug.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. A257025E02
    Using SST and a hammer, tap in the tight plug as shown in the illustration.
    SST
    09950-60010   (09951-00550)
    09950-70010   (09951-07100)

    Standard depth:
    0.2 to 0.5 mm (0.00787 to 0.0197 in.)

    Text in Illustration 
    *a
    0.2 to 0.5 mm

← DISASSEMBLY (Sep 2011 – Dec 2011)INSPECTION (from Sep 2011) →