2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P062D Fuel Injector Driver Circuit Performance Bank1

Diagnostic trouble codes · Vehicles built from Jan 2012

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The EDU delivers drive signals to fuel injectors using the DC/DC converter, which provides a high-voltage and quick-charging system.
Soon after the EDU receives a fuel injection command (IJT) signal from the ECM, the EDU responds to the command with an injector injection confirmation (IJF) signal when the current is applied to the fuel injector.
A165473E04
P062D 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idling for 10 seconds
Open or short in the No. 1 injector driver (EDU) or fuel injector circuit (1 trip detection logic).
  1. Open or short in No. 1 injector driver (EDU) circuit
  2. Fuel injector
  3. No. 1 EDU
  4. ECM
P062E 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idling for 10 seconds
Open or short in the No. 2 injector driver (EDU) or fuel injector circuit (1 trip detection logic).
  1. Open or short in No. 2 injector driver (EDU) circuit
  2. Fuel injector
  3. No. 2 EDU
  4. ECM

MONITOR DESCRIPTION

  1. P062D, P062E (Open or short in EDU or fuel injector circuit):
    The ECM continuously monitors both injection command (IJT) signals and injection confirmation (IJF) signals. This DTC will be stored if the ECM determines that the number of IJT signals and IJF signals are inconsistent.
    The fuel injectors are grounded over a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the EDU (injector drive circuit) in relation to the current drawn by the fuel injector. When the fuel injector current becomes too high, the voltage drop over the resistor exceeds a specified level and no IJF signal for that cylinder is sent to the ECM.
    After the engine is started, when there is no injection confirmation (IJF) signal from the No. 1 or No. 2 EDU to the ECM even though the ECM sends injection command (IJT) signals to the No. 1 or No. 2 EDU, DTC P062D or DTC P062E is stored.
    If this DTC is stored, the ECM enters fail-safe mode and limits engine power or stops the engine. The fail-safe mode continues until the ignition switch is turned off.
    A145849E05

WIRING DIAGRAM

A182478E01
A263486E01
A182478E06
A275256E02

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing a fuel injector, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK TERMINAL VOLTAGE EDU POWER SOURCE
  1. Disconnect the No. 1 injector driver (EDU) connectors.

  1. A130531E05
    Disconnect the No. 2 injector driver (EDU) connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    No. 1 
    Tester Connection
    Switch Condition
    Specified Condition
    C74-8 (+B) - C73-1 (GND)
    Ignition switch ON
    11 to 14 V
    No. 2 
    Tester Connection
    Switch Condition
    Specified Condition
    C76-8 (+B) - C75-1 (GND)
    Ignition switch ON
    11 to 14 V



NG
Go to step 7
OK


2. INSPECT INJECTOR DRIVER (No. 1 and No. 2)

  1. A176216
    Interchange the No. 1 and No. 2 EDU connectors.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear the DTCs (Click here).

    NOTICE:
    Before clearing the DTCs, write them down.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTCs do not change
    A
    DTCs change (change in malfunctioning cylinder or EDU code)
    B



B
Go to step 8
A


3. INSPECT FUEL INJECTOR (RESISTANCE)

  1. A165911E02
    Disconnect the fuel injector connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    0.85 to 1.05 Ω



NG
Go to step 9
OK


4. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - EDU)
A182481E01
A182481E02
  1. Disconnect the fuel injector connectors.

  1. Disconnect the No. 1 EDU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    No. 1 
    Tester Connection
    Condition
    Specified Condition
    C5-2 - C74-4 (INJ1)
    Always
    Below 1 Ω
    C14-2 - C74-3 (INJ4)
    Always
    Below 1 Ω
    C69-2 - C74-2 (INJ6)
    Always
    Below 1 Ω
    C68-2 - C74-1 (INJ7)
    Always
    Below 1 Ω
    C5-1 - C74-5 (COM1)
    Always
    Below 1 Ω
    C14-1 - C74-5 (COM1)
    Always
    Below 1 Ω
    C69-1 - C74-6 (COM2)
    Always
    Below 1 Ω
    C68-1 - C74-6 (COM2)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    No. 1 
    Tester Connection
    Condition
    Specified Condition
    C5-2 or C74-4 (INJ1) - Body ground
    Always
    10 kΩ or higher
    C14-2 or C74-3 (INJ4) - Body ground
    Always
    10 kΩ or higher
    C69-2 or C74-2 (INJ6) - Body ground
    Always
    10 kΩ or higher
    C68-2 or C74-1 (INJ7) - Body ground
    Always
    10 kΩ or higher
    C5-1 or C74-5 (COM1) - Body ground
    Always
    10 kΩ or higher
    C14-1 or C74-5 (COM1) - Body ground
    Always
    10 kΩ or higher
    C69-1 or C74-6 (COM2) - Body ground
    Always
    10 kΩ or higher
    C68-1 or C74-6 (COM2) - Body ground
    Always
    10 kΩ or higher

  1. Disconnect the fuel injector connectors.

  1. Disconnect the No. 2 EDU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    No. 2 
    Tester Connection
    Condition
    Specified Condition
    C70-2 - C76-4 (INJ2)
    Always
    Below 1 Ω
    C9-2 - C76-3 (INJ5)
    Always
    Below 1 Ω
    C67-2 - C76-1 (INJ3)
    Always
    Below 1 Ω
    C54-2 - C76-2 (INJ8)
    Always
    Below 1 Ω
    C70-1 - C76-5 (COM4)
    Always
    Below 1 Ω
    C9-1 - C76-5 (COM4)
    Always
    Below 1 Ω
    C67-1 - C76-6 (COM5)
    Always
    Below 1 Ω
    C54-1 - C76-6 (COM5)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    No. 2 
    Tester Connection
    Condition
    Specified Condition
    C70-2 or C76-4 (INJ2) - Body ground
    Always
    10 kΩ or higher
    C9-2 or C76-3 (INJ5) - Body ground
    Always
    10 kΩ or higher
    C67-2 or C76-1 (INJ3) - Body ground
    Always
    10 kΩ or higher
    C54-2 or C76-2 (INJ8) - Body ground
    Always
    10 kΩ or higher
    C70-1 or C76-5 (COM4) - Body ground
    Always
    10 kΩ or higher
    C9-1 or C76-5 (COM4) - Body ground
    Always
    10 kΩ or higher
    C67-1 or C76-6 (COM5) - Body ground
    Always
    10 kΩ or higher
    C54-1 or C76-6 (COM5) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 10
OK


5. CHECK HARNESS AND CONNECTOR (EDU - ECM)

  1. A182482E01
    Disconnect the No. 1 EDU connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    No. 1 (for LHD) 
    Tester Connection
    Condition
    Specified Condition
    C73-6 (#10) - C45-40 (#1)
    Always
    Below 1 Ω
    C73-5 (#40) - C45-37 (#4)
    Always
    Below 1 Ω
    C73-3 (#60) - C45-35 (#6)
    Always
    Below 1 Ω
    C73-2 (#70) - C45-34 (#7)
    Always
    Below 1 Ω
    C73-7 (INJF) - C45-61 (INJF)
    Always
    Below 1 Ω
    No. 1 (for RHD) 
    Tester Connection
    Condition
    Specified Condition
    C73-6 (#10) - C46-40 (#1)
    Always
    Below 1 Ω
    C73-5 (#40) - C46-37 (#4)
    Always
    Below 1 Ω
    C73-3 (#60) - C46-35 (#6)
    Always
    Below 1 Ω
    C73-2 (#70) - C46-34 (#7)
    Always
    Below 1 Ω
    C73-7 (INJF) - C46-61 (INJF)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    No. 1 (for LHD) 
    Tester Connection
    Condition
    Specified Condition
    C73-6 (#10) or C45-40 (#1) - Body ground
    Always
    10 kΩ or higher
    C73-5 (#40) or C45-37 (#4) - Body ground
    Always
    10 kΩ or higher
    C73-3 (#60) or C45-35 (#6) - Body ground
    Always
    10 kΩ or higher
    C73-2 (#70) or C45-34 (#7) - Body ground
    Always
    10 kΩ or higher
    C73-7 (INJF) or C45-61 (INJF) - Body ground
    Always
    10 kΩ or higher
    No. 1 (for RHD) 
    Tester Connection
    Condition
    Specified Condition
    C73-6 (#10) or C46-40 (#1) - Body ground
    Always
    10 kΩ or higher
    C73-5 (#40) or C46-37 (#4) - Body ground
    Always
    10 kΩ or higher
    C73-3 (#60) or C46-35 (#6) - Body ground
    Always
    10 kΩ or higher
    C73-2 (#70) or C46-34 (#7) - Body ground
    Always
    10 kΩ or higher
    C73-7 (INJF) or C46-61 (INJF) - Body ground
    Always
    10 kΩ or higher

  1. A182482E02
    Disconnect the No. 2 EDU connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    No. 2 (for LHD) 
    Tester Connection
    Condition
    Specified Condition
    C75-6 (#20) - C45-39 (#2)
    Always
    Below 1 Ω
    C75-2 (#30) - C45-38 (#3)
    Always
    Below 1 Ω
    C75-5 (#50) - C45-36 (#5)
    Always
    Below 1 Ω
    C75-3 (#80) - C45-33 (#8)
    Always
    Below 1 Ω
    C75-7 (INF2) - C45-60 (INF2)
    Always
    Below 1 Ω
    No. 2 (for RHD) 
    Tester Connection
    Condition
    Specified Condition
    C75-6 (#20) - C46-39 (#2)
    Always
    Below 1 Ω
    C75-2 (#30) - C46-38 (#3)
    Always
    Below 1 Ω
    C75-5 (#50) - C46-36 (#5)
    Always
    Below 1 Ω
    C75-3 (#80) - C46-33 (#8)
    Always
    Below 1 Ω
    C75-7 (INF2) - C46-60 (INF2)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    No. 2 (for LHD) 
    Tester Connection
    Condition
    Specified Condition
    C75-6 (#20) or C45-39 (#2) - Body ground
    Always
    10 kΩ or higher
    C75-2 (#30) or C45-38 (#3) - Body ground
    Always
    10 kΩ or higher
    C75-5 (#50) or C45-36 (#5) - Body ground
    Always
    10 kΩ or higher
    C75-3 (#80) or C45-33 (#8) - Body ground
    Always
    10 kΩ or higher
    C75-7 (INF2) or C45-60 (INF2) - Body ground
    Always
    10 kΩ or higher
    No. 2 (for RHD) 
    Tester Connection
    Condition
    Specified Condition
    C75-6 (#20) or C46-39 (#2) - Body ground
    Always
    10 kΩ or higher
    C75-2 (#30) or C46-38 (#3) - Body ground
    Always
    10 kΩ or higher
    C75-5 (#50) or C46-36 (#5) - Body ground
    Always
    10 kΩ or higher
    C75-3 (#80) or C46-33 (#8) - Body ground
    Always
    10 kΩ or higher
    C75-7 (INF2) or C46-60 (INF2) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 10
OK


6. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 11
7. GO TO INJECTOR CIRCUIT
  1. Go to the injector circuit (Click here).



NEXT
Go to step 11
8. REPLACE INJECTOR DRIVER (No. 1 or No. 2)
  1. Replace the injector driver (No. 1 or No. 2) (Click here).



NEXT
Go to step 11
9. REPLACE FUEL INJECTOR
  1. Replace the fuel injector (Click here).



NEXT
Go to step 11
10. REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT


11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine and idle it for 10 seconds.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END


← P062D Fuel Injector Driver Circuit Performance Bank1 (+ P062E) (Sep 2011 – Dec 2011)P1229 Fuel Pump System (Sep 2011 – Dec 2011) →