2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

Injector Circuit

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The injector driver drives the injectors at high speeds with a high-voltage DC/DC converter. The ECM constantly monitors the injector driver and stops the engine if an abnormal condition is detected.

WIRING DIAGRAM

Refer to DTC P062D (Click here).

INSPECTION PROCEDURE


1. CHECK EDU (POWER SOURCE)
  1. Disconnect the No. 1 injector driver (EDU) connectors.

  1. A130531E05
    Disconnect the No. 2 injector driver (EDU) connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    No. 1 
    Tester Connection
    Switch Condition
    Specified Condition
    C74-8 (+B) - C73-1 (GND)
    Ignition switch ON
    11 to 14 V
    No. 2 
    Tester Connection
    Switch Condition
    Specified Condition
    C76-8 (+B) - C75-1 (GND)
    Ignition switch ON
    11 to 14 V



NG
Go to step 2
OK

REPLACE INJECTOR DRIVER (No. 1 or No. 2) (Click here)

2. INSPECT FUSE (EFI)
A182599E01
  1. Remove the EFI MAIN and EFI MAIN 2 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    EFI MAIN fuse
    Always
    Below 1 Ω
    EFI MAIN 2 fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


3. INSPECT EDU RELAY (EDU 1 OR EDU 2)
  1. Inspect the EDU relay (EDU 1 or EDU 2) (Click here).



NG
REPLACE EDU RELAY (EDU 1 OR EDU 2)
OK


4. INSPECT INTEGRATION NO.1 RELAY (EFI OR EFI MAIN 2)
  1. Inspect the Integration relay (EFI or EFI MAIN 2) (Click here).



NG
REPLACE INTEGRATION NO.1 RELAY
OK


5. CHECK HARNESS AND CONNECTOR (EDU RELAY - EDU)
A182600E01
  1. Remove the EDU relay (EDU 1 or EDU 2) from the engine room relay block.

  1. Remove the EDU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    No. 1 
    Tester Connection
    Condition
    Specified Condition
    EDU 1 relay (5) - C74-8 (+B)
    Always
    Below 1 Ω
    No. 2 
    Tester Connection
    Condition
    Specified Condition
    EDU 2 relay (5) - C76-8 (+B)
    Always
    Below 1 Ω
    Standard Resistance (Check for Short):
    No. 1 
    Tester Connection
    Condition
    Specified Condition
    EDU 1 relay (5) or C74-8 (+B) - Body ground
    Always
    10 kΩ or higher
    No. 2 
    Tester Connection
    Condition
    Specified Condition
    EDU 2 relay (5) or C76-8 (+B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (EDU RELAY - ECM)
A182601E01
  1. Remove the EDU relay (EDU 1 or EDU 2) from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    No. 1 (LHD) 
    Tester Connection
    Condition
    Specified Condition
    EDU 1 relay (2) - A38-45 (IREL)
    Always
    Below 1 Ω
    No. 2 (LHD) 
    Tester Connection
    Condition
    Specified Condition
    EDU 2 relay (2) - A38-46 (IRL2)
    Always
    Below 1 Ω
    No. 1 (RHD) 
    Tester Connection
    Condition
    Specified Condition
    EDU 1 relay (2) - A52-45 (IREL)
    Always
    Below 1 Ω
    No. 2 (RHD) 
    Tester Connection
    Condition
    Specified Condition
    EDU 2 relay (2) - A52-46 (IRL2)
    Always
    Below 1 Ω
    Standard Resistance (Check for Short):
    No. 1 (LHD) 
    Tester Connection
    Condition
    Specified Condition
    EDU 1 relay (2) or A38-45 (IREL) - Body ground
    Always
    10 kΩ or higher
    No. 2 (LHD) 
    Tester Connection
    Condition
    Specified Condition
    EDU 2 relay (2) or A38-46 (IRL2) - Body ground
    Always
    10 kΩ or higher
    No. 1 (RHD) 
    Tester Connection
    Condition
    Specified Condition
    EDU 1 relay (2) or A52-45 (IREL) - Body ground
    Always
    10 kΩ or higher
    No. 2 (RHD) 
    Tester Connection
    Condition
    Specified Condition
    EDU 2 relay (2) or A52-46 (IRL2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - EDU RELAY, ECM, BODY GROUND)
A182602E01
A182603E01
  1. Remove the integration relay from the engine room relay block.

  1. Remove the EDU relay (EDU 1 or EDU 2).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    No. 1 
    Tester Connection
    Condition
    Specified Condition
    1B-4 - EDU 1 relay (1)
    Always
    Below 1 Ω
    1B-4 - EDU 1 relay (3)
    Always
    Below 1 Ω
    No. 2 
    Tester Connection
    Condition
    Specified Condition
    1A-4 - EDU 2 relay (1)
    Always
    Below 1 Ω
    1A-4 - EDU 2 relay (3)
    Always
    Below 1 Ω
    Standard Resistance (Check for Short):
    No. 1 
    Tester Connection
    Condition
    Specified Condition
    E1B-4 or EDU 1 relay (1) - Body ground
    Always
    10 kΩ or higher
    1B-4 or EDU 1 relay (3) - Body ground
    Always
    10 kΩ or higher
    No. 2 
    Tester Connection
    Condition
    Specified Condition
    1A-4 or EDU 2 relay (1) - Body ground
    Always
    10 kΩ or higher
    1A-4 or EDU 2 relay (3) - Body ground
    Always
    10 kΩ or higher

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    No. 1 (LHD) 
    Tester Connection
    Condition
    Specified Condition
    1B-2 - A38-44 (MREL)
    Always
    Below 1 Ω
    1B-3 - Body ground
    Always
    Below 1 Ω
    No. 2 (LHD) 
    Tester Connection
    Condition
    Specified Condition
    1A-2 - A38-44 (MREL)
    Always
    Below 1 Ω
    1A-3 - Body ground
    Always
    Below 1 Ω
    No. 1 (RHD) 
    Tester Connection
    Condition
    Specified Condition
    1B-2 - A52-44 (MREL)
    Always
    Below 1 Ω
    1B-3 - Body ground
    Always
    Below 1 Ω
    No. 2 (RHD) 
    Tester Connection
    Condition
    Specified Condition
    1A-2 - A52-44 (MREL)
    Always
    Below 1 Ω
    1A-3 - Body ground
    Always
    Below 1 Ω
    Standard Resistance (Check for Short):
    No. 1 (LHD) 
    Tester Connection
    Condition
    Specified Condition
    1B-2 or A38-44 (MREL) - Body ground
    Always
    10 kΩ or higher
    No. 2 (LHD) 
    Tester Connection
    Condition
    Specified Condition
    1A-2 or A38-44 (MREL) - Body ground
    Always
    10 kΩ or higher
    No. 1 (RHD) 
    Tester Connection
    Condition
    Specified Condition
    1B-2 or A52-44 (MREL) - Body ground
    Always
    10 kΩ or higher
    No. 2 (RHD) 
    Tester Connection
    Condition
    Specified Condition
    1A-2 or A52-44 (MREL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK HARNESS AND CONNECTOR (EDU - BODY GROUND)

  1. A166686E02
    Disconnect the EDU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    No. 1 
    Tester Connection
    Condition
    Specified Condition
    C73-1 (GND) - Body ground
    Always
    Below 1 Ω

    Standard Resistance:
    No. 2 
    Tester Connection
    Condition
    Specified Condition
    C75-1 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (EDU - BODY GROUND)
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)


← Injector Circuit (Sep 2011 – Dec 2011)Brake Override System (Sep 2011 – Dec 2011) →