2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0180 Fuel Temperature Sensor "A" Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The fuel temperature sensor monitors the fuel temperature. The fuel temperature sensor has a thermistor that varies its resistance depending on the fuel temperature. When the fuel temperature is low, the resistance of the thermistor is high. When the temperature is high, the resistance is low. The variations of resistance are communicated to the ECM as changes of voltage (See Fig. 1).
The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via resistor R.
Resistor R and the fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes due to a change of fuel temperature, the voltage at terminal THF also changes. Based on this signal, the ECM corrects the pressure control compensation of the fuel supply pump and determines if there are errors.
G036559E03
P0180 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 0.5 seconds
Open or short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
  1. Open or short in fuel temperature sensor circuit
  2. Fuel temperature sensor
  3. ECM
P0182 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 0.5 seconds
Short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
  1. Short in fuel temperature sensor circuit
  2. Fuel temperature sensor
  3. ECM
P0183 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 0.5 seconds
Open in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
  1. Open in fuel temperature sensor circuit
  2. Fuel temperature sensor
  3. ECM
Related Data List 
DTC No.
Data List
P0180
Fuel Temp
P0182
P0183

HINT:
  1. If DTC P0180, P0182 and/or P0183 is stored, the following symptoms may appear:
    1. Misfire
    2. Combustion noise
    3. Black smoke
    4. Lack of power


WIRING DIAGRAM

A184084E01

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. If DTCs relating to different systems are stored, and they share terminal E2 as their ground, check this ground circuit first.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (FUEL TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / Fuel Temp.

  1. Read the value.

    OK:
    Same value as the actual fuel temperature.

    Result 
    Result
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or more
    B
    OK (Same as actual fuel temperature)
    C

    HINT:
    1. If there is an open circuit, the tester indicates -40°C (-40°F).
    2. If there is a short circuit, the tester indicates 140°C (284°F) or more.



B
Go to step 6

C
Go to step 11
A


2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

  1. A184098E01
    Disconnect the fuel temperature sensor connector.

  1. Connect terminals 2 (THF) and 1 (E2) of the fuel temperature sensor connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / Fuel Temp.

  1. Read the value.

    OK:
    140°C (284°F) or higher



NG
Go to step 4
OK


3. CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE FUEL TEMPERATURE SENSOR
  1. Replace the fuel temperature sensor (Click here).



NEXT
Go to step 11
4. CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)

  1. A184080E01
    Disconnect the fuel temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    Fuel temperature sensor connector-2 (THF) - C45-116 (THF)
    Always
    Below 1 Ω
    Fuel temperature sensor connector-1 (E2) - C45-75 (E2)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    Fuel temperature sensor connector-2 (THF) - C46-116 (THF)
    Always
    Below 1 Ω
    Fuel temperature sensor connector-1 (E2) - C46-75 (E2)
    Always
    Below 1 Ω



NG
Go to step 10
OK


5. CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 11
6. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

  1. A166688E06
    Disconnect the fuel temperature sensor connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / Fuel Temp.

  1. Read the value.

    OK:
    -40°C (-40°F)



NG
Go to step 8
OK


7. REPLACE FUEL TEMPERATURE SENSOR
  1. Replace the fuel temperature sensor (Click here).



NEXT
Go to step 11
8. CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)

  1. A184080E02
    Disconnect the fuel temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    Fuel temperature sensor connector-2 (THF) or C45-116 (THF) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    Fuel temperature sensor connector-2 (THF) or C46-116 (THF) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 10
OK


9. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 11
10. REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT


11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON for 1 second.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0168 Fuel Temperature Too High (from Jan 2012)P0180 Fuel Temperature Sensor "A" Circuit (+ P0182, P0183) (from Jan 2012) →