2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0180 Fuel Temperature Sensor "A" Circuit

Diagnostic trouble codes · Vehicles built from Jan 2012

Also covers:

DESCRIPTION

The fuel temperature sensor monitors the fuel temperature. The fuel temperature sensor has a thermistor that varies its resistance depending on the fuel temperature. When the fuel temperature is low, the resistance of the thermistor is high. When the temperature is high, the resistance is low. The variations of resistance are communicated to the ECM as changes of voltage (See Fig. 1).
The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via resistor R.
Resistor R and the fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes due to a change in fuel temperature, the voltage at terminal THF also changes. Based on this signal, the ECM corrects the pressure control compensation of the fuel supply pump assembly.
A208462E01
P0180 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Engine switch on (IG) for 0.5 seconds
Open or short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
  1. Open or short in fuel temperature sensor circuit
  2. Fuel temperature sensor (fuel supply pump assembly)
  3. ECM
P0182 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Engine switch on (IG) for 0.5 seconds
Short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
  1. Short in fuel temperature sensor circuit
  2. Fuel temperature sensor (fuel supply pump assembly)
  3. ECM
P0183 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Engine switch on (IG) for 0.5 seconds
Open in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
  1. Open in fuel temperature sensor circuit
  2. Fuel temperature sensor (fuel supply pump assembly)
  3. ECM
Related Data List 
DTC No.
Data List
P0180
P0182
P0183
Fuel Temp

HINT:
  1. If DTC P0180, P0182 and/or P0183 is stored, the following symptoms may appear:
    1. Misfire
    2. Combustion noise
    3. Black smoke
    4. Lack of power


WIRING DIAGRAM

A184084E02

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  3. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING GTS (FUEL TEMPERATURE)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Enter the following menus: Engine and ECT / Data List / Fuel Temp.

  1. Read the value.

    OK:
    Same as the actual fuel temperature

    Result 
    Result
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or higher
    B
    OK (Same as actual fuel temperature)
    C

    HINT:
    1. If there is an open circuit, the GTS indicates -40°C (-40°F).
    2. If there is a short circuit, the GTS indicates 140°C (284°F) or higher.



B
Go to step 5

C
Go to step 12
A


2. READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

  1. A204471E21
    Disconnect the fuel temperature sensor connector.

  1. Connect terminals 2 and 1 of the fuel temperature sensor connector.

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Enter the following menus: Engine and ECT / Data List / Fuel Temp.

  1. Read the value.

    OK:
    140°C (284°F) or higher

    Text in Illustration 
    *1
    Fuel Temperature Sensor
    *2
    ECM
    *a
    Front view of wire harness connector
    (to Fuel Temperature Sensor)

  1. Reconnect the fuel temperature sensor connector.



OK
Go to step 6
NG


3. CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
  1. Disconnect the fuel temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    z65-2 (THF) - C45-116 (THF)
    Always
    Below 1 Ω
    z65-1 (E2) - C45-92 (E2)
    Always
    Below 1 Ω


    Standard Resistance:
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    z65-2 (THF) - C46-116 (THF)
    Always
    Below 1 Ω
    z65-1 (E2) - C46-92 (E2)
    Always
    Below 1 Ω

  1. Reconnect the fuel temperature sensor connector.

  1. Reconnect the ECM connector.



NG
Go to step 11
OK


4. CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.
  1. Replace the ECM (Click here).



NEXT
Go to step 12
5. READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

  1. A204586E04
    Disconnect the fuel temperature sensor connector.

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Enter the following menus: Engine and ECT / Data List / Fuel Temp.

  1. Read the value.

    OK:
    -40°C (-40°F)

    Text in Illustration 
    *1
    Fuel Temperature Sensor
    *2
    ECM

  1. Reconnect the fuel temperature sensor connector.



NG
Go to step 7
OK


6. REPLACE FUEL SUPPLY PUMP ASSEMBLY (FUEL TEMPERATURE SENSOR)
  1. Replace the fuel supply pump assembly (fuel temperature sensor) (Click here).



NEXT
Go to step 9
7. CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
  1. Disconnect the fuel temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    z65-2 (THF) or C45-116 (THF) - Body ground
    Always
    10 kΩ or higher


    Standard Resistance:
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    z65-2 (THF) or C46-116 (THF) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the fuel temperature sensor connector.

  1. Reconnect the ECM connector.



NG
Go to step 11
OK


8. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 12
9. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).

  1. Perform PM forced regeneration (Click here).

    HINT:
    When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.


NEXT


10. PERFORM SUPPLY PUMP INITIALIZATION
  1. Perform supply pump initialization (Click here).



NEXT
Go to step 12
11. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


12. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch on (IG) for 1 second or more.

  1. Enter the following menus: Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input (+ P0123, P0222, P0223) (from Jan 2012)P0201 Injector Circuit / Open - (Cylinder 1) (+ 9 more codes) (from Jan 2012) →