2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

ON-VEHICLE INSPECTION

Inspection · Vehicles built Sep 2011 – Dec 2011


CHECK AIR PRESSURE SENSOR
  1. Remove the intake manifold (Click here).

  1. Disconnect the air pressure sensor connector.

  1. Turn the engine switch on (IG).

  1. A180778E03
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (VC) - 1 (E2)
    Engine switch on (IG)
    4.5 to 5.5 V

  1. Turn the engine switch off.

  1. G032742E02
    Connect the air pressure sensor connector.

  1. Connect SST (turbocharger pressure gauge) to the air pressure sensor as shown in the illustration.

    SST
    09992-00242  

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester main switch on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (absolute).

    OK:
    Pressure fluctuates in response to the pressure applied with pressure gauge.

  1. Check that the pressure displayed on the intelligent tester fluctuates when applying pressure to the pressure sensor with the pressure gauge.


CHECK VACUUM CONTROL VALVE SET

  1. A179567
    Disconnect the 2 connectors.

  1. Disconnect the 2 vacuum switching valve hoses and 2 vacuum hoses from the VSV.

  1. A113126E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    33 to 39 Ω
    1 - Body ground
    Always
    1 MΩ or higher
    2 - Body ground
    1 MΩ or higher

    If the resistance is not as specified, replace the VSV.

  1. A113127E01
    Apply air to the port as shown in the illustration.

  1. Check that air does not flow from port A.
    If the result is not as specified, replace the VSV.

  1. A113128E01
    Apply positive battery voltage to the terminals, apply air to the port, and check that air flows from the port shown in the illustration.
    If the result is not as specified, replace the VSV.

  1. Connect the 2 vacuum switching valve hoses and 2 vacuum hoses to the VSV.

    NOTICE:
    Be sure to connect the vacuum hoses correctly.

  1. Connect the 2 VSV connectors.

  1. Perform the "Check Vacuum Switching Valve" procedures above on the other VSV.


CHECK NO. 1 AIR SWITCHING VALVE ASSEMBLY

  1. A182805
    Disconnect the vacuum switching valve hose from the VSV for the air injection system.

  1. Apply vacuum of 60 kPa (450 mmHg, 17.7 in.Hg) to the vacuum switching valve hose, and check that the vacuum does not decrease.
    If the operation is not as specified, replace the No. 1 air switching valve assembly.

  1. A179570
    Release the vacuum, and check that the operation sound is emitted from the No. 1 air switching valve assembly.
    If the operation is not as specified, replace the No. 1 air switching valve assembly.


CHECK NO. 2 AIR SWITCHING VALVE ASSEMBLY

  1. A113129
    Disconnect the vacuum switching valve hose from the VSV for the air injection system.

  1. Apply vacuum of 60 kPa (450 mmHg, 17.7 in.Hg) to the vacuum switching valve hose, and check that the vacuum does not decrease.
    If the operation is not as specified, replace the No. 2 air switching valve assembly.

  1. A179569
    Release the vacuum, and check that the operation sound is emitted from the No. 2 air switching valve assembly.
    If the operation is not as specified, replace the No. 2 air switching valve assembly.

← COMPONENTS (Sep 2011 – Dec 2011)REMOVAL (Sep 2011 – Dec 2011) →