2011-2013 Land Cruiser · Service Manual Suspension

ECU Power Source Circuit

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This circuit supplies the power source to the suspension control ECU.

WIRING DIAGRAM

C177465E01

INSPECTION PROCEDURE

NOTICE:
  1. Before performing troubleshooting, inspect the connectors of related circuits.
  2. If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (Click here).


1. READ VALUE USING INTELLIGENT TESTER (IG POWER SOURCE VOLTAGE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and the tester on.

  1. Read the "IG Power Source Voltage" item in the Data List.

    AHC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG Power Source Voltage
    Power supply voltage /
    min.: 0 V
    max.: 255 V
    Engine switch on (IG): 11 to 14 V
    -

    OK:
    11 to 14 V



NG
Go to step 2
OK

CHECK INDICATOR CIRCUIT (Click here)

2. INSPECT FUSE (ECU-IG NO. 4)
  1. Remove the ECU-IG No. 4 fuse from the cowl side junction block RH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU-IG No. 4 fuse
    Always
    Below 1 Ω



NG
Go to step 7
OK


3. INSPECT COWL SIDE JUNCTION BLOCK RH (IG NO. 4 RELAY)
  1. Disconnect the K34 ECU connector.

  1. C175386E01
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    K34-5 (IG) - Body ground
    Engine switch on (IG)
    11 to 14 V



NG
Go to step 4
OK

REPLACE SUSPENSION CONTROL ECU (Click here)

4. CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK RH - ECU AND BODY GROUND)
C177467E01
  1. Disconnect the K34 and K35 ECU connectors.

  1. Disconnect the 3C cowl side junction block RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K34-5 (IG) - 3C-5
    Always
    Below 1 Ω
    K34-1 (GND) - Body ground
    Always
    Below 1 Ω
    K35-6 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (BATTERY - COWL SIDE JUNCTION BLOCK RH)
  1. Disconnect the 3A cowl side junction block RH connector.

  1. E142217E08
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3A-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - COWL SIDE JUNCTION BLOCK RH AND BODY GROUND)
  1. Disconnect the 3C cowl side junction block RH connector.

  1. C177469E01
    Measure the voltage and resistance according to the value(s) in the tables below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3C-22 - Body ground
    Engine switch on (IG)
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3C-8 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK RH - ECU)
  1. Disconnect the K34 ECU connector.

  1. C175386E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K34-5 (IG) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If a fuse is blown, replace the fuse.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COWL SIDE JUNCTION BLOCK RH


← ECU Power Source Circuit (Sep 2011 – Dec 2011)COMPONENTS (from Sep 2011) →