2011-2013 Land Cruiser · Service Manual Suspension

C1741 Front Height Control Solenoid Valve RH Circuit Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The control valve solenoid assembly consists of each front and rear leveling valve, gate valve and accumulator valve. It performs the height control and connects and disconnects the fluid line of the right and left shock absorber by operating the solenoid valve with the control signal from the ECU.
DTC Code
Detection Condition
Trouble Area
C1741
When either of the following is detected:
  1. With the front leveling valve RH not activated, an open signal of the front leveling valve RH is detected for 1 second or more.
  2. With the front leveling valve RH activated, a short signal of the front leveling valve RH is detected 8 times successively.
  1. Harness or connector
  2. No. 1 height control valve
  3. Suspension control ECU
  4. Each front suspension control valve (Each front spring rate switching valve)
C1742
When either of the following is detected:
  1. With the front leveling valve LH not activated, an open signal of the front leveling valve LH is detected for 1 second or more.
  2. With the front leveling valve LH activated, a short signal of the front leveling valve LH is detected 8 times successively.
  1. Harness or connector
  2. No. 1 height control valve
  3. Suspension control ECU
  4. Each front suspension control valve (Each front spring rate switching valve)
C1743
When either of the following is detected:
  1. With the rear leveling valve RH not activated, an open signal of the rear leveling valve RH is detected for 1 second or more.
  2. With the rear leveling valve RH activated, a short signal of the rear leveling valve RH is detected 8 times successively.
  1. Harness or connector
  2. No. 1 height control valve
  3. Suspension control ECU
  4. Each front suspension control valve (Each front spring rate switching valve)
C1744
When either of the following is detected:
  1. With the rear leveling valve LH not activated, an open signal of the rear leveling valve LH is detected for 1 second or more.
  2. With the rear leveling valve LH activated, a short signal of the rear leveling valve LH is detected 8 times successively.
  1. Harness or connector
  2. No. 1 height control valve
  3. Suspension control ECU
  4. Each front suspension control valve (Each front spring rate switching valve)
C1753
When either of the following is detected:
  1. With the accumulator valve not activated, an open signal of the accumulator valve is detected for 1 second or more.
  2. With the accumulator valve activated, a short signal of the accumulator valve is detected 8 times successively.
  1. Harness or connector
  2. No. 1 height control valve
  3. Suspension control ECU
  4. Each front suspension control valve (Each front spring rate switching valve)
C1754
When either of the following is detected:
  1. With the front gate valve not activated, an open signal of the front gate valve is detected for 1 second or more.
  2. With the front gate valve activated, a short signal of the front gate valve is detected 8 times successively.
  1. Harness or connector
  2. No. 1 height control valve
  3. Suspension control ECU
  4. Each front suspension control valve (Each front spring rate switching valve)
C1755
When either of the following is detected:
  1. With the rear gate valve not activated, an open signal of the rear gate valve is detected for 1 second or more.
  2. With the rear gate valve activated, a short signal of the rear gate valve is detected 8 times successively.
  1. Harness or connector
  2. No. 1 height control valve
  3. Suspension control ECU
  4. Each front suspension control valve (Each front spring rate switching valve)

WIRING DIAGRAM

C177456E01

INSPECTION PROCEDURE

NOTICE:
  1. Before performing troubleshooting, inspect the connectors of related circuits.
  2. If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (Click here).

HINT:
Power is supplied to the No. 1 height control valve and front suspension control valve from the suspension control ECU. If a short occurs in the power supply circuit in the front suspension control valve, DTC C1741, C1742, C1743, C1744, C1753, C1754 and/or C1755 will be stored. In this case, DTC C1736 and/or C1737 will also be stored.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (NO. 1 HEIGHT CONTROL VALVE)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Select the Active Test mode on the intelligent tester.

  1. Check the operation of the leveling valve solenoid, accumulator valve solenoid and gate valve solenoid when operating the solenoid with the intelligent tester.

    AHC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Front Right Height Solenoid
    Front height control solenoid valve RH
    ON or OFF
    Operation of solenoid can be heard.
    Front Left Height Solenoid
    Front height control solenoid valve LH
    ON or OFF
    Operation of solenoid can be heard.
    Rear Right Height Solenoid
    Rear height control solenoid valve RH
    ON or OFF
    Operation of solenoid can be heard.
    Rear Left Height Solenoid
    Rear height control solenoid valve LH
    ON or OFF
    Operation of solenoid can be heard.
    Accumulator Valve
    Accumulator solenoid valve
    ON or OFF
    Operation of solenoid can be heard.
    Front Gate Valve
    Front gate solenoid valve
    ON or OFF
    When the Front Gate Valve item of the Active Test is operated, the Front Gate Valve item of the Data List changes to ON/OFF.
    Rear Gate Valve
    Rear gate solenoid valve
    ON or OFF
    When the Rear Gate Valve item of the Active Test is operated, the Rear Gate Valve item of the Data List changes to ON/OFF.

    OK:
    The leveling valve solenoid, accumulator solenoid and/or gate valve solenoid operates.



NG
Go to step 3
OK


2. RECONFIRM DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Perform a road test.

  1. Check for DTCs.

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE SUSPENSION CONTROL ECU (Click here)

3. CHECK HARNESS AND CONNECTOR (NO. 1 HEIGHT CONTROL VALVE - SUSPENSION CONTROL ECU)
  1. Disconnect the N4 No. 1 height control valve connector.

  1. Disconnect the K36 ECU connector.C174880E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K36-1 (SLB) - N4-6 (SLB)
    Always
    Below 1 Ω
    K36-7 (SLFR) - N4-4 (SLFR)
    Always
    Below 1 Ω
    K36-7 (SLFR) - Body ground
    Always
    10 kΩ or higher
    K36-8 (SLFL) - N4-3 (SLFL)
    Always
    Below 1 Ω
    K36-8 (SLFL) - Body ground
    Always
    10 kΩ or higher
    K36-9 (SLRR) - N4-1 (SLRR)
    Always
    Below 1 Ω
    K36-9 (SLRR) - Body ground
    Always
    10 kΩ or higher
    K36-10 (SLAC) - N4-7 (AHC-)
    Always
    Below 1 Ω
    K36-10 (SLAC) - Body ground
    Always
    10 kΩ or higher
    K36-22 (SLRL) - N4-2 (SLRL)
    Always
    Below 1 Ω
    K36-22 (SLRL) - Body ground
    Always
    10 kΩ or higher
    K36-29 (SLRG) - N4-5 (SLRG)
    Always
    Below 1 Ω
    K36-29 (SLRG) - Body ground
    Always
    10 kΩ or higher
    K36-30 (SLFG) - N4-8 (SLFG)
    Always
    Below 1 Ω
    K36-30 (SLFG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (BODY GROUND BETWEEN ECU - NO. 1 HEIGHT CONTROL VALVE)
  1. Disconnect the N4 No. 1 height control valve connector.

  1. C174826E05
    Disconnect the K36 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K36-1 (SLB) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 6
OK


5. INSPECT NO. 1 HEIGHT CONTROL VALVE
  1. Connect the N4 No. 1 height control valve connector.

  1. Disconnect the K36 ECU connector.

  1. C174826E06
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K36-7 (SLFR) - K36-1 (SLB)
    Always
    3 to 3.8 Ω
    K36-7 (SLFR) - Body ground
    Always
    10 kΩ or higher
    K36-8 (SLFL) - K36-1 (SLB)
    Always
    3 to 3.8 Ω
    K36-8 (SLFL) - Body ground
    Always
    10 kΩ or higher
    K36-9 (SLRR) - K36-1 (SLB)
    Always
    3 to 3.8 Ω
    K36-9 (SLRR) - Body ground
    Always
    10 kΩ or higher
    K36-10 (SLAC) - K36-1 (SLB)
    Always
    3 to 3.8 Ω
    K36-10 (SLAC) - Body ground
    Always
    10 kΩ or higher
    K36-22 (SLRL) - K36-1 (SLB)
    Always
    3 to 3.8 Ω
    K36-22 (SLRL) - Body ground
    Always
    10 kΩ or higher
    K36-29 (SLRG) - K36-1 (SLB)
    Always
    3 to 3.8 Ω
    K36-29 (SLRG) - Body ground
    Always
    10 kΩ or higher
    K36-30 (SLFG) - K36-1 (SLB)
    Always
    3 to 3.8 Ω
    K36-30 (SLFG) - Body ground
    Always
    10 kΩ or higher
    K36-1 (SLB) - Body ground
    Always
    10 kΩ or higher



NG
REPLACE NO. 1 HEIGHT CONTROL VALVE (Click here)
OK

REPLACE SUSPENSION CONTROL ECU (Click here)

6. CHECK HARNESS AND CONNECTOR (BODY GROUND BETWEEN ECU - FRONT SUSPENSION CONTROL VALVE)
  1. Disconnect the N10 and N12 front suspension control valve connectors.

  1. Disconnect the N4 No. 1 height control valve connector.

  1. Disconnect the K36 ECU connector.

  1. C174826E04
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K36-1 (SLB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - FRONT SUSPENSION CONTROL VALVE)
  1. Disconnect the N10*1 and/or N12*2 front suspension control valve connector.

    HINT:
    *1: for RH
    *2: for LH

  1. Disconnect the K36 ECU connector.C174926E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K36-11 (CRFR) - N10-1 (CRFR)
    Always
    Below 1 Ω
    K36-11 (CRFR) - Body ground
    Always
    10 kΩ or higher
    K36-23 (CRFL) - N12-1 (CRFL)
    Always
    Below 1 Ω
    K36-23 (CRFL) - Body ground
    Always
    10 kΩ or higher
    K36-1 (SLB) - N10-2 (SLB)
    Always
    Below 1 Ω
    K36-1 (SLB) - N12-2 (SLB)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT SUSPENSION CONTROL VALVE


← C1736 Front Suspension Control Valve RH Malfunction (+ C1737) (from Jan 2012)C1741 Front Height Control Solenoid Valve RH Circuit Malfunction (+ 6 more codes) (from Jan 2012) →