2011-2013 Land Cruiser · Service Manual Suspension

C1763 Abnormal Pump Motor Oil Pressure

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

DTC Code
Detection Condition
Trouble Area
C1763
While the motor relay is in operation, the condition that the fluid pressure is 0.6 MPa (6.1 kgf/cm2, 87 psi) or less continues for 0.6 seconds.
  1. Harness or connector
  2. Suspension control relay
  3. Height control pump and motor
  4. Suspension control ECU

WIRING DIAGRAM

C176979E01

INSPECTION PROCEDURE

NOTICE:
  1. Before performing troubleshooting, inspect the connectors of related circuits.
  2. If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (Click here).


1. INSPECT SUSPENSION CONTROL RELAY (AHC)
  1. Remove the suspension control relay from the engine room relay block.

  1. C149624E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminal 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminal 1 and 2
    Below 1 Ω



NG
REPLACE SUSPENSION CONTROL RELAY
OK


2. CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - RELAY (AHC) AND BODY GROUND)
C176974E01
  1. Remove the suspension control relay from the engine room relay block.

  1. Disconnect the K36 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K36-16 (RC) - Relay block suspension control relay terminal 1
    Always
    Below 1 Ω
    K36-16 (RC) - Body ground
    Always
    10 kΩ or higher
    Relay block suspension control relay terminal 2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (BATTERY - SUSPENSION CONTROL RELAY)
  1. Remove the suspension control relay from the engine room relay block.

  1. C177031E01
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Relay block suspension control relay terminal 5 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL RELAY - PUMP AND MOTOR AND BODY GROUND)
  1. Remove the suspension control relay from the engine room relay block.

  1. Disconnect the L36 pump and motor connector.

  1. Measure the resistance according to the value(s) in the table below.C177032E01

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Relay block suspension control relay terminal 3 - L36-2
    Always
    Below 1 Ω
    Relay block suspension control relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    L36-1 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK OPERATION OF HEIGHT CONTROL PUMP AND MOTOR

  1. C177053E01
    Remove the height control pump and motor (Click here).

  1. Apply battery voltage to the height control pump and motor and check the operation of the motor.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 2
    Battery negative (-) → Terminal 1
    Motor operates

    NOTICE:
    1. Be careful of fluid spray when the height control pump and motor is operating.
    2. Do not allow the motor to operate for 60 seconds or more.
    3. If the height control pump and motor is shorted, locked, or has a similar type of malfunction, a large amount of current will be flowing. Therefore, if the motor does not operate, immediately stop this inspection.



NG
REPLACE HEIGHT CONTROL PUMP AND MOTOR (Click here)
OK

REPLACE SUSPENSION CONTROL ECU (Click here)


← C1756 Suspension Control Relay Malfunction (from Jan 2012)C1763 Abnormal Pump Motor Oil Pressure (from Jan 2012) →