C1763 Abnormal Pump Motor Oil Pressure
Diagnostic trouble codes · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
| DTC Code |
Detection Condition |
Trouble Area |
| C1763 |
While the motor relay is in operation, the condition that the fluid pressure is 0.6 MPa (6.1 kgf/cm2, 87 psi) or less continues for 0.6 seconds. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Before performing troubleshooting, inspect the connectors of related circuits.
- If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (Click here).
- Before performing troubleshooting, inspect the connectors of related circuits.
| 1. INSPECT SUSPENSION CONTROL RELAY (AHC) |
Remove the suspension control relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage is not applied to terminal 1 and 2
10 kΩ or higher
Battery voltage is applied to terminal 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - RELAY (AHC) AND BODY GROUND) |


Remove the suspension control relay from the engine room relay block.
Disconnect the K36 ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
K36-16 (RC) - Relay block suspension control relay terminal 1
Always
Below 1 Ω
K36-16 (RC) - Body ground
Always
10 kΩ or higher
Relay block suspension control relay terminal 2 - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (BATTERY - SUSPENSION CONTROL RELAY) |
Remove the suspension control relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Condition
Specified Condition
Relay block suspension control relay terminal 5 - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL RELAY - PUMP AND MOTOR AND BODY GROUND) |
Remove the suspension control relay from the engine room relay block.
Disconnect the L36 pump and motor connector.
Measure the resistance according to the value(s) in the table below.


- Standard Resistance:
Tester Connection
Condition
Specified Condition
Relay block suspension control relay terminal 3 - L36-2
Always
Below 1 Ω
Relay block suspension control relay terminal 3 - Body ground
Always
10 kΩ or higher
L36-1 - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK OPERATION OF HEIGHT CONTROL PUMP AND MOTOR |
Remove the height control pump and motor (Click here).

Apply battery voltage to the height control pump and motor and check the operation of the motor.
- OK:
Measurement Condition
Specified Condition
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1
Motor operates
- NOTICE:
- Be careful of fluid spray when the height control pump and motor is operating.
- Do not allow the motor to operate for 60 seconds or more.
- If the height control pump and motor is shorted, locked, or has a similar type of malfunction, a large amount of current will be flowing. Therefore, if the motor does not operate, immediately stop this inspection.
- Be careful of fluid spray when the height control pump and motor is operating.
|
|
||||
| OK | ||
| ||
