2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

VC Output Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The ECM constantly generates 5 V power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
A116143E65
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the engine switch is first turned on (IG). The MIL goes off when the engine is started.


WIRING DIAGRAM

A239478E03
A239479E02

INSPECTION PROCEDURE


1. CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the engine switch on (IG).

    OK:
    MIL lights up



NG
Go to step 2
OK

SYSTEM OK

2. CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and tester on.

  1. Check the communication between the tester and ECM.

    Result 
    Result
    Proceed to
    Communication is possible
    A
    Communication is not possible
    B



A
GO TO MIL CIRCUIT (Click here)
B


3. CHECK MIL (THROTTLE POSITION SENSOR)
  1. Disconnect the C3 throttle body connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE THROTTLE BODY ASSEMBLY (Click here)
B


4. CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the A31 accelerator pedal position sensor connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE ACCELERATOR PEDAL POSITION SENSOR (Click here)
B


5. CHECK MIL (POWER STEERING OIL PRESSURE SENSOR)
  1. Disconnect the C59 power steering oil pressure sensor connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE POWER STEERING OIL PRESSURE SENSOR (Click here)
B


6. CHECK MIL (CAMSHAFT POSITION SENSOR)
  1. Disconnect the C99 camshaft position sensor connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE CAMSHAFT POSITION SENSOR (Click here)
B


7. CHECK MIL (CRANKSHAFT POSITION SENSOR)
  1. Disconnect the C114 crankshaft position sensor connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
B


8. CHECK MIL (VVT SENSOR for Intake Side of Bank 1)
  1. Disconnect the C100 VVT sensor (for Intake Side of Bank 1) connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE VVT SENSOR (for Intake Side of Bank 1) (Click here)
B


9. CHECK MIL (VVT SENSOR for Exhaust Side of Bank 1)
  1. Disconnect the C121T sensor (for Exhaust Side of Bank 1) connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE VVT SENSOR (for Exhaust Side of Bank 1) (Click here)
B


10. CHECK MIL (VVT SENSOR for Intake Side of Bank 2)
  1. Disconnect the C101 VVT sensor (for Intake Side of Bank 2) connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE VVT SENSOR (for Intake Side of Bank 2) (Click here)
B


11. CHECK MIL (VVT SENSOR for Exhaust Side of Bank 2)
  1. Disconnect the C122T sensor (for Exhaust Side of Bank 2) connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE VVT SENSOR (for Exhaust Side of Bank 2) (Click here)
B


12. CHECK HARNESS AND CONNECTOR
  1. Disconnect the C3throttle body connector.

  1. Disconnect the A31 accelerator pedal position sensor connector.

  1. Disconnect the C59 power steering oil pressure sensor connector.

  1. Disconnect the C99 camshaft position sensor connector.

  1. Disconnect the C114 crankshaft position sensor connector.

  1. Disconnect the C100 VVT sensor (for Intake Side of Bank 1) connector.

  1. Disconnect the C121 VVT sensor (for Exhaust Side of Bank 1) connector.

  1. Disconnect the C101 VVT sensor (for Intake Side of Bank 2) connector.

  1. Disconnect the C122 VVT sensor (for Exhaust Side of Bank 2) connector.

  1. A164740E24
    Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C45-80 (VCTA) - Body ground
    Always
    10 kΩ or higher
    A38-57 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A38-59 (VCP2) - Body ground
    Always
    10 kΩ or higher
    C45-66 (VCV2) - Body ground
    Always
    10 kΩ or higher
    C45-67 (VCV1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← ECM Power Source Circuit (from Jan 2012)VC Output Circuit (from Jan 2012) →