2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

ECM Power Source Circuit

Circuit diagnosis · Vehicles built from Jan 2012

DESCRIPTION

When the engine switch is turned on (IG), the battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil of the No. 1 integration relay (EFI relay), closing the contacts and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM

A278625E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK NO. 1 INTEGRATION RELAY (POWER SOURCE)
A185979E02
  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1C-1 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    No. 1 Integration relay
    *a
    Front view of wire harness connector
    (to No. 1 Integration Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - BATTERY)
OK


2. INSPECT NO. 1 INTEGRATION RELAY (EFI)
  1. Inspect the No. 1 integration relay (EFI) (Click here).



NG
REPLACE NO. 1 INTEGRATION RELAY
OK


3. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM, BODY GROUND)
  1. Check the harness and connectors between the No. 1 integration relay and ECM.

    1. Remove the No. 1 integration relay from the engine room relay block.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      A52-34 (MREL) - 1B-2
      Always
      Below 1 Ω
      A52-3 (+B) - 1B-4
      Always
      Below 1 Ω
      A52-2 (+B2) - 1B-4
      Always
      Below 1 Ω
      A52-34 (MREL) or 1B-2 - Body ground
      Always
      10 kΩ or higher
      A52-3 (+B) or 1B-4 - Body ground
      Always
      10 kΩ or higher
      A52-2 (+B2) or 1B-4 - Body ground
      Always
      10 kΩ or higher
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      A38-34 (MREL) - 1B-2
      Always
      Below 1 Ω
      A38-3 (+B) - 1B-4
      Always
      Below 1 Ω
      A38-2 (+B2) - 1B-4
      Always
      Below 1 Ω
      A38-34 (MREL) or 1B-2 - Body ground
      Always
      10 kΩ or higher
      A38-3 (+B) or 1B-4 - Body ground
      Always
      10 kΩ or higher
      A38-2 (+B2) or 1B-4 - Body ground
      Always
      10 kΩ or higher

  1. Check the harness and connectors between the No. 1 integration relay and body ground.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1B-3 - Body ground
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C46-81 (E1) - Body ground
    Always
    Below 1 Ω
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C45-81 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT ECM (IGSW VOLTAGE)
A182331E14
  1. Disconnect the ECM connectors.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    A52-28 (IGSW) - C46-81 (E1)
    Engine switch on (IG)
    11 to 14 V
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    A38-28 (IGSW) - C45-81 (E1)
    Engine switch on (IG)
    11 to 14 V

    Text in Illustration 
    *A
    for RHD
    *B
    for LHD
    *a
    Front view of wire harness connector
    (to ECM)



NG
Go to step 6
OK

REPLACE ECM (Click here)

6. INSPECT NO. 1 INTEGRATION RELAY (IG2)
  1. Inspect the No. 1 integration relay (IG2) (Click here).



NG
REPLACE NO. 1 INTEGRATION RELAY
OK


7. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    1B-8 - A52-28 (IGSW)
    Always
    Below 1 Ω
    1B-8 or A52-28 (IGSW) - Body ground
    Always
    10 kΩ or higher
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    1B-8 - A38-28 (IGSW)
    Always
    Below 1 Ω
    1B-8 or A38-28 (IGSW) - Body ground
    Always
    10 kΩ or higher


    Result:
    Result
    Proceed to
    Out of normal range
    A
    Within normal range
    B



B
Go to step 8
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

8. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - MAIN BODY ECU, BODY GROUND)
  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Disconnect the Main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1B-6 - E2-11 (IG2D)
    Always
    Below 1 Ω
    1B-7 - Body ground
    Always
    Below 1 Ω
    E2-11 (IG2D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ENTRY AND START SYSTEM (Click here)


← P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) (+ P2A03) (from Jan 2012)VC Output Circuit (from Jan 2012) →