2011-2013 Land Cruiser · Service Manual Vehicle Interior

Power Source Mode does not Change

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When the certification ECU (smart key ECU assembly) has detected the key inside the cabin before the brake pedal (for A/T) or clutch pedal (for M/T) is depressed, the power source mode can be changed in the following order sequentially by pressing the engine switch: off → on (ACC) → on (IG) → off.
When one of the DTCs shown in the illustration below is detected, troubleshoot the DTC(s) by following the troubleshooting procedure relevant to the DTC(s). If the power source mode still cannot be changed normally, despite troubleshooting, one of the following may have occurred:
  1. The LIN communication line is malfunctioning.
  2. The certification ECU (smart key ECU assembly) has determined that no key is inside the cabin.
  3. The engine switch is malfunctioning.
  4. The main body ECU is malfunctioning.
A175421E05

WIRING DIAGRAM

A175473E01

INSPECTION PROCEDURE

HINT:
If the vehicle is in key cancel mode, change to normal mode (Click here).


1. CHECK DTC OUTPUT
  1. Check whether a DTC is output (Click here).

    Result 
    Result
    Proceed to
    No DTC output
    A
    DTC output
    B



B
GO TO ENTRY AND START SYSTEM (FOR START FUNCTION) (DIAGNOSTIC TROUBLE CODE CHART) (Click here)
A


2. CHECK ENTRY AND START SYSTEM
B311542E03
  1. Remove the battery of the electrical key transmitter (Click here).

  1. With the brake pedal (for A/T) or clutch pedal (for M/T) depressed, touch the key to the engine switch, as shown in the illustration.

  1. When operating the engine switch, check whether the engine switch changes to on (ACC) or on (IG).

HINT:
  1. When the electrical key transmitter cannot be verified even when it is in the operational area, the engine start check can be performed by removing the transmitter battery from the electrical key transmitter and holding the transmitter against the engine switch.
  2. When performing the check, if the engine switch turns on (ACC) or on (IG), there is a problem with key certification inside the cabin.

Result 
Result
Proceed to
Does not change to on (ACC)
A
Does not change to on (IG)
B
Does not change to on (ACC) and on (IG)
C
Changes to on (ACC) and on (IG)
D


B
Go to step 5

C
Go to step 11

D
GO TO ENTRY AND START SYSTEM (FOR ENTRY FUNCTION) (ROOM OSCILLATOR DOES NOT RECOGNIZE KEY) (Click here)
A


3. INSPECT FUSE (AM2)
  1. Remove the AM2 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    AM2 fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


4. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
A175407E01
  1. Disconnect the E1, E2, 2A and 2D main body ECU connectors.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E1-6 (AM1) - Body ground
    Always
    11 to 14 V
    E2-1 (AM2) - Body ground
    Always
    11 to 14 V
    2A-1 - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E1-22 (ACCD) - 2D-45
    Always
    Below 1 Ω
    2D-62 (GND2) - Body ground
    Always
    Below 1 Ω
    E1-22 (ACCD) or 2D-45 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

5. INSPECT FUSE (AM2)
  1. Remove the AM2 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    AM2 fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


6. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
A175407E02
  1. Disconnect the E1, E2, 2A and 2D main body ECU connectors.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E1-6 (AM1) - Body ground
    Always
    11 to 14 V
    E2-1 (AM2) - Body ground
    Always
    11 to 14 V
    2A-1 - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E1-3 (IG1D) - 2D-43
    Always
    Below 1 Ω
    2D-62 (GND2) - Body ground
    Always
    Below 1 Ω
    E1-3 (IG1D) or 2D-43 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT INTEGRATION RELAY (IG2 RELAY)
A175471E01
  1. Remove the integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1B-8 - 1C-1
    Battery voltage applied to terminals 1B-6 and 1B-7
    Below 1 Ω
    1B-8 - 1C-1
    Battery voltage not applied to terminals 1B-6 and 1B-7
    10 kΩ or higher



NG
REPLACE INTEGRATION NO.1 RELAY (IG2 RELAY)
OK


8. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INTEGRATION RELAY (IG2 RELAY))
A175472E01
  1. Disconnect the E2 main body ECU connector.

  1. Disconnect the 1B integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E2-11 (IG2D) - 1B-6
    Always
    Below 1 Ω
    1B-7 - Body ground
    Always
    Below 1 Ω
    E2-11 (IG2D) or 1B-6 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT FUSE (IGN, IG2 MAIN)
  1. Remove the IGN fuse and IG2 MAIN fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IGN fuse
    Always
    Below 1 Ω
    IG2 MAIN fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


10. CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - INTEGRATION RELAY (IG2 RELAY))
A175474E01
  1. Disconnect the E26 steering lock ECU connector.

  1. Disconnect the 1B and 1C integration relay connectors.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1C-1 - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E26-6 (IG2) - 1B-8
    Always
    Below 1 Ω
    E26-6 (IG2) or 1B-8 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

11. INSPECT FUSE (AM2)
  1. Remove the AM2 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    AM2 fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


12. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
A175398E01
  1. Disconnect the E1, E2 and 2D main body ECU connectors.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E1-6 (AM1) - Body ground
    Always
    11 to 14 V
    E2-1 (AM2) - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2D-62 (GND2) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13. INSPECT ENGINE SWITCH
C164809E04
  1. Disconnect the E18 engine switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    7 (SS1) - 5 (GND)
    Pushed
    Below 1 Ω
    2 (SS2) - 5 (GND)
    Pushed
    Below 1 Ω
    7 (SS1) - 5 (GND)
    Not pushed
    10 kΩ or higher
    2 (SS2) - 5 (GND)
    Not pushed
    10 kΩ or higher

    Result 
    Result
    Proceed to
    Within specified range
    A
    Outside specified range (for 1GR-FE)
    B
    Outside specified range (for 1UR-FE)
    C
    Outside specified range (for 3UR-FE)
    D
    Outside specified range (for 1VD-FTV)
    E



B
REPLACE ENGINE SWITCH (Click here)

C
REPLACE ENGINE SWITCH (Click here)

D
REPLACE ENGINE SWITCH (Click here)

E
REPLACE ENGINE SWITCH (Click here)
A


14. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ENGINE SWITCH AND BODY GROUND)
C162990E04
  1. Disconnect the E1 main body ECU connector.

  1. Disconnect the E18 engine switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E1-17 (SSW1) - E18-7 (SS1)
    Always
    Below 1 Ω
    E1-16 (SSW2) - E18-2 (SS2)
    Always
    Below 1 Ω
    E18-5 (GND) - Body ground
    Always
    Below 1 Ω
    E1-17 (SSW1) or E18-7 (SS1) - Body ground
    Always
    10 kΩ or higher
    E1-16 (SSW2) or E18-2 (SS2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← Power Source Mode does not Change (Sep 2011 – Dec 2011)Engine does not Start (Sep 2011 – Dec 2011) →