2011-2013 Land Cruiser · Service Manual Brake

FAIL-SAFE CHART

System information · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


FAIL-SAFE OPERATION
  1. If there is a problem with sensor signals or hydraulic brake booster systems, the skid control ECU prohibits power supply to the hydraulic brake booster and informs the ECM of VSC system failure.
    The hydraulic brake booster turns off each solenoid and the ECM shuts off VSC control (traction control signal) from the skid control ECU accordingly, which turns out to be as if the Multi-terrain ABS, A-TRC and VSC systems were not installed.
    The Multi-terrain ABS control will be prohibited, but EBD control continues as much as possible. If EBD control is impossible, the BRAKE warning light comes on to warn the driver (Click here).
  2. If system components have any malfunction before starting control, the fail-safe function immediately stops the operation.
    If system components have any malfunction during control, the fail-safe function gradually stops the control so as not to trigger a sudden change in vehicle conditions.
    If it is impossible to control the systems, the warning light comes on to inform the driver of termination of the systems (Click here).

HINT:
If the hydraulic brake booster encounters a malfunction, brake performance is gradually lost and Multi-terrain ABS, BA, A-TRC, VSC, CRAWL and hill-start assist control system control is prohibited.

  1. Multi-terrain ABS, EBD and BA system:

    Malfunction Area
    Control Method
    Multi-terrain ABS system
    Multi-terrain ABS, BA, A-TRC, VSC, CRAWL and hill-start assist control control prohibited
    BA system
    Multi-terrain ABS, BA, A-TRC, VSC, CRAWL and hill-start assist control control prohibited
    EBD system
    Multi-terrain ABS, EBD, BA, A-TRC, VSC, CRAWL and hill-start assist control control prohibited

  2. A-TRC, VSC, CRAWL and hill-start assist control system:

    HINT:
    As for the A-TRC, VSC, CRAWL and hill-start assist control systems, different systems prohibit different controls according to the malfunctioning part.

    Malfunction Area
    Control Method
    Engine control system
    (A-TRC and VSC systems)
    Before control: Disables control
    During control: Uses only brakes to perform control
    Brake control system
    (VSC system)
    Before control: Disables control
    During control: Uses only engine to perform control
    Brake control system
    (A-TRC, CRAWL and hill-start assist control systems)
    Before control: Disables control
    During control: Disables control (by gradually ending control)


SYSTEM TEMPERATURE PROTECTION OPERATION
If the A-TRC, CRAWL or hill-start assist control system has been used constantly for a long time, the temperature of the hydraulic brake booster may excessively increase. If the temperature excessively increases, the skid control buzzer will sound intermittently. If the temperature increases even more, the skid control buzzer sounds for 3 seconds and the indicator light either comes on or blinks.
System
Indicator Condition
A-TRC, and hill-start assist control systems
SLIP indicator light comes on.
CRAWL system
SLIP indicator light comes on.
CRAWL indicator light blinks and then turns off.

HINT:
  1. When the CRAWL indicator light turns off after blinking, CRAWL temporarily becomes nonfunctional, but after the temperature has decreased, pressing the CRAWL switch again will activate CRAWL (Even when the temperature decreases, CRAWL will not reactivate automatically).
  2. If the Slip indicator light goes off (as for the CRAWL system, the CRAWL indicator light also comes on), the systems automatically return to normal operating conditions.
  3. As this is not a malfunction, no DTC will be stored.

← FREEZE FRAME DATA (from Jan 2012)FAIL-SAFE CHART (from Jan 2012) →