C1253 Pump Motor Relay
Diagnostic trouble codes · Vehicles built from Jan 2012
DESCRIPTION
The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU (master cylinder solenoid).| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1253 |
There is a motor system circuit (motor input circuit) malfunction. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the master cylinder solenoid, perform zero point calibration and store the system information (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- After replacing the master cylinder solenoid, perform zero point calibration and store the system information (Click here).
| 1. PERFORM ACTIVE TEST USING GTS (MOTOR RELAY) |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
ABS/VSC/TRC Tester Display
Test Part
Control Range
Diagnostic Note
Motor Relay
Motor relay
Relay ON/OFF
An operating sound of the motor can be heard.
Check the operating sound of the motor individually when operating it with the GTS.
- OK:
- An operating sound of the motor can be heard.
|
|
||||
| OK | |
| 2. RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Depress the brake pedal more than 40 times.
Turn the ignition switch to ON.
Wait until the pump motor stops.
Depress the brake pedal several times until the pump motor turns on. (Procedure A)
Wait until the pump stops. (Procedure B)
Repeat the above steps (procedure A and B) 3 more times.
Check if the same DTC is output (Click here).
- HINT:
- Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.
Result Result
Proceed to
DTC is not output
A
DTC is output (for LHD)
B
DTC is output (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 3. CHECK HARNESS AND CONNECTOR (+BM1/+BM2 TERMINAL) |
Turn the ignition switch off.
Disconnect the skid control ECU (master cylinder solenoid) connectors.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Condition
Specified Condition
A24-2 (+BM1) - Body ground
Always
11 to 14 V
A25-2 (+BM2) - Body ground
Always
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the skid control ECU (master cylinder solenoid) connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A24-1 (GND1) - Body ground
Always
Below 1 Ω
A24-32 (GND2) - Body ground
Always
Below 1 Ω
A25-4 (GND3) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])
|
|
||||
| OK | |
| 5. RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Depress the brake pedal more than 40 times.
Turn the ignition switch to ON.
Wait until the pump motor stops.
Depress the brake pedal several times until the pump motor turns on. (Procedure A)
Wait until the pump stops. (Procedure B)
Repeat the above steps (procedure A and B) 3 more times.
Check if the same DTC is output (Click here).
- HINT:
- Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.
Result Result
Proceed to
DTC is not output
A
DTC is output (for LHD)
B
DTC is output (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||

