2011-2013 Land Cruiser · Service Manual Brake

C1253/53 Pump Motor Relay Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU.
DTC Code
DTC Detection Condition
Trouble Area
C1253/53
There is a motor system circuit (motor input circuit) malfunction.
  1. Hydraulic brake booster pump motor
  2. Hydraulic brake booster pump motor circuit

WIRING DIAGRAM

C173280E01

INSPECTION PROCEDURE

NOTICE:
When replacing the hydraulic brake booster assembly (master cylinder solenoid), perform zero point calibration (Click here).


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MOTOR RELAY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Start the engine.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Motor Relay
    Motor relay
    Relay ON/OFF
    An operation sound of the motor can be heard.

  1. Check the operation sound of the motor individually when operating it with the intelligent tester.

    OK:
    The operation sound of the motor can be heard.



NG
Go to step 3
OK


2. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Depress the brake pedal more than 20 times.

  1. Turn the ignition switch to ON.

  1. Wait until the pump motor stops.

  1. Depress the brake pedal several times until the pump motor turns on. (Procedure A)

  1. Wait until the pump stops. (Procedure B)

  1. Repeat the above steps (procedure A and B) 3 more times.

  1. Check if the same DTC is output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    for LHD
    B
    for RHD
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

3. INSPECT SKID CONTROL ECU (+BM TERMINAL)

  1. C124799E42
    Disconnect the A24 and A25 skid control ECU connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A24-2 (+BM1) - Body ground
    Always
    11 to 14 V
    A25-2 (+BM2) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT SKID CONTROL ECU (GND TERMINAL)

  1. C124799E41
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A24-32 (GND2) - Body ground
    Always
    Below 1 Ω
    A25-4 (GND3) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Depress the brake pedal more than 20 times.

  1. Turn the ignition switch to ON.

  1. Wait until the pump motor stops.

  1. Depress the brake pedal several times until the pump motor turns on. (Procedure A)

  1. Wait until the pump stops. (Procedure B)

  1. Repeat the above steps (procedure A and B) 3 more times.

  1. Check if the same DTC is output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    for LHD
    B
    for RHD
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← C1253 Pump Motor Relay (from Jan 2012)C1254 Pressure Sensor or Switch (from Jan 2012) →