2011-2013 Land Cruiser · Service Manual Vehicle Exterior

License Plate Light Circuit

Circuit diagnosis · Vehicles built from Sep 2011

DESCRIPTION

When the light switch TAIL signal is received from the cowl side junction block ECU, the license plate light illuminates.

WIRING DIAGRAM

E234119E02

INSPECTION PROCEDURE


1. INSPECT FUSE (TAIL FUSE)
  1. Remove the TAIL fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    TAIL fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


2. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY)
E157348E01
  1. Disconnect the 2A ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    2A-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK VEHICLE TYPE
  1. Check the vehicle type.

    Result 
    Result
    Proceed to
    for Double Swing Out Type
    A
    except Double Swing Out Type, w/ Tire Carrier
    B
    except Double Swing Out Type, w/o Tire Carrier
    C



B
Go to step 5

C
Go to step 6
A


4. CHECK HARNESS AND CONNECTOR (LICENSE PLATE LIGHT - MAIN BODY ECU AND BODY GROUND)
E234120E03
  1. Disconnect the 2C ECU connector.

  1. Disconnect the W2 light connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2C-22 - W2-1 (B)
    Always
    Below 1 Ω
    W2-2 (E) - Body ground
    W2-1 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

5. CHECK HARNESS AND CONNECTOR (LICENSE PLATE LIGHT - MAIN BODY ECU AND BODY GROUND)
E234120E04
  1. Disconnect the 2C ECU connector.

  1. Disconnect the h2 light connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2C-22 - h2-1
    Always
    Below 1 Ω
    h2-2 - Body ground
    h2-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

6. CHECK HARNESS AND CONNECTOR (LICENSE PLATE LIGHT - MAIN BODY ECU AND BODY GROUND)
E157464E04
  1. Disconnect the 2C ECU connector.

  1. for LH:

    1. Disconnect the S3 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2C-22 - S3-1
      Always
      Below 1 Ω
      S3-2 - Body ground
      S3-1 - Body ground
      Always
      10 kΩ or higher

  1. for RH:

    1. Disconnect the S2 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2C-22 - S2-1
      Always
      Below 1 Ω
      S2-2 - Body ground
      S2-1 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← Engine Switch Illumination Circuit (from Sep 2011)Illumination Circuit (Sep 2011 – Dec 2011) →