2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Illumination Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When a door is opened while the DOOR switch of the map light assembly is on, the map light assembly receives a door open signal from the main body ECU and turns on the corresponding lights.

WIRING DIAGRAM

E161623E01
E161619E01

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Operate the intelligent tester according to the steps on the display and select "Active Test".

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Illuminated Entry System
    Illumination light
    OFF or ON
    -

OK:
Light comes on.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT FUSE (DOME2)
  1. Remove the DOME2 fuse from the engine room junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DOME2 fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


3. CHECK VEHICLE TYPE
  1. Check the vehicle type.

    Result 
    Result
    Proceed to
    w/o Map Light
    A
    w/ Map Light
    B



B
Go to step 5
A


4. CHECK HARNESS AND CONNECTOR (DOME LIGHT - MAP LIGHT AND BODY GROUND)
  1. Disconnect the 2D ECU connector.

  1. Disconnect the R13 light connector.E161887E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2D-51 (ILE) - R13-2 (CTY)
    Always
    Below 1 Ω
    R13-1 (B) - Body ground
    R13-3 (E) - Body ground
    2D-51 (ILE) - Body ground
    Always
    10 kΩ or higher

  1. Disconnect the R15 light connector.E161887E02

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2D-51 (ILE) - R15-2 (DL)
    Always
    Below 1 Ω
    R15-1 (DB) - Body ground
    R15-3 (L) - Body ground
    2D-51 (ILE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE MAIN BODY ECU

5. CHECK HARNESS AND CONNECTOR (MAP LIGHT - BODY GROUND)

  1. E157935E03
    Disconnect the 2D ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    R7-16 (+B3) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6. INSPECT MAP LIGHT
E157935E01
  1. Remove the map light (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    R7-31 (+B1) - R7-5 (RRVT)
    Dome light switch off
    Below 1 V
    Dome light switch on
    11 to 14 V
    R7-6 (RILL) - R7-32 (ILLB)
    Dome light switch off
    Below 1 V
    Dome light switch on
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    R7-9 (CTY) - Body ground
    "Door" switch on and door open
    Below 1 Ω
    "Door" switch off and door open
    10 kΩ or higher
    "Door" switch on and door closed
    10 kΩ or higher
    "Door" switch off and door closed
    10 kΩ or higher
    R7-17 (GND9) - Body ground
    Always
    Below 1 Ω



NG
REPLACE MAP LIGHT (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (NO. 3 ROOM LIGHT - MAP LIGHT AND BODY GROUND)
  1. Disconnect the R7 map light connector.

  1. E157941E04
    Disconnect the R6 light connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R7-31 (+B1) - R6-1 (DB)
    Always
    Below 1 Ω
    R7-5 (RRVT) - R6-3 (DL)
    R6-2 (L) - Body ground
    R7-31 (+B1) - Body ground
    Always
    10 kΩ or higher
    R7-16 (RRVT) - Body ground



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


8. CHECK VEHICLE TYPE
  1. Check the vehicle type.

    Result 
    Result
    Proceed to
    w/ Sliding Roof
    A
    w/o Sliding Roof
    B



B
Go to step 10
A


9. CHECK HARNESS AND CONNECTOR (SPOT LIGHT - MAP LIGHT AND BODY GROUND)
  1. Disconnect the R7 map light connector.

  1. E157934E02
    Disconnect the R4 light connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R7-32 (ILLB) - R4-1 (B)
    Always
    Below 1 Ω
    R7-6 (RILL) - R4-2 (CTY)
    R7-32 (ILLB) - Body ground
    Always
    10 kΩ or higher
    R7-6 (RILL) - Body ground

  1. E157944E02
    for LH:
    1. Disconnect the R8 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      R7-32 (ILLB) - R8-2 (BL)
      Always
      Below 1 Ω
      R7-1 (RGND) - R8-4 (E)
      R7-32 (ILLB) - Body ground
      Always
      10 kΩ or higher
      R7-1 (RGND) - Body ground

  1. for RH:

    1. Disconnect the R9 light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      R7-32 (ILLB) - R9-2 (BR)
      Always
      Below 1 Ω
      R7-1 (RGND) - R9-4 (ER)
      R7-32 (ILLB) - Body ground
      Always
      10 kΩ or higher
      R7-1 (RGND) - Body ground



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE MAIN BODY ECU

10. CHECK HARNESS AND CONNECTOR (NO. 1 ROOM LIGHT - MAP LIGHT AND BODY GROUND)
  1. Disconnect the R7 map light connector.

  1. E157941E06
    Disconnect the R12 light connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R7-32 (ILLB) - R12-1 (B)
    Always
    Below 1 Ω
    R7-6 (RILL) - R12-3 (CTY)
    R12-2 (E) - R7-1 (RGND)
    R7-32 (ILLB) - Body ground
    Always
    10 kΩ or higher
    R7-6 (RILL) - Body ground



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE MAIN BODY ECU


← License Plate Light Circuit (from Sep 2011)Illumination Circuit (from Jan 2012) →