2011-2013 Land Cruiser · Service Manual Power Source / Network

ECM Communication Stop Mode

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

Detection Item
Symptom
Trouble Area
ECM Communication Stop Mode
Either condition is met:
  1. "ECM (Engine)" is not displayed on the "Bus Check" screen.
  2. "ECM Communication Stop Mode" in "DTC Communication Table" applies.
  1. Power source or inside of ECM
  2. ECM

WIRING DIAGRAM

C158954E18
C180131E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)

  1. Disconnect the A52 and C46 ECU connectors.C234869E08

    Text in Illustration 
    *A
    except 1VD-FTV
    *B
    for 1VD-FTV
    *a
    Front view of wire harness connector
    (to ECM)
    -
    -

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    except 1VD-FTV 
    Tester Connection
    Condition
    Specified Condition
    C46-81 (E1) - Body ground
    Always
    Below 1 Ω
    C46-42 (E02) - Body ground
    Always
    Below 1 Ω
    C46-43 (E01) - Body ground
    Always
    Below 1 Ω
    C46-82 (ME01) - Body ground
    Always
    Below 1 Ω

    for 1VD-FTV 
    Tester Connection
    Condition
    Specified Condition
    A52-32 (EC) - Body ground
    Always
    Below 1 Ω
    C46-81 (E1) - Body ground
    Always
    Below 1 Ω
    C46-21 (E02) - Body ground
    Always
    Below 1 Ω
    C46-22 (E01) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    except 1VD-FTV 
    Tester Connection
    Condition
    Specified Condition
    A52-1 (BATT) - Body ground
    Always
    11 to 14 V
    A52-2 (+B2) - Body ground
    Battery positive (+) voltage applied to terminal A52-34 (MREL)
    11 to 14 V
    A52-3 (+B) - Body ground
    Battery positive (+) voltage applied to terminal A52-34 (MREL)
    11 to 14 V

    for 1VD-FTV 
    Tester Connection
    Condition
    Specified Condition
    A52-20 (BATT) - Body ground
    Always
    11 to 14 V
    A52-44 (MREL) - Body ground
    Ignition switch ON
    11 to 14 V
    A52-2 (+B) - Body ground
    Battery positive (+) voltage applied to terminal A52-44 (MREL)
    11 to 14 V

Result 
Result
Proceed to
OK (for 1GR-FE)
A
OK (for 1UR-FE)
B
OK (for 1VD-FTV)
C
NG
D


B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE ECM (Click here)


← ECM Communication Stop Mode (Sep 2011 – Dec 2011)Main Body ECU Communication Stop Mode (Sep 2011 – Dec 2011) →