2011-2013 Land Cruiser · Service Manual Power Source / Network

ECM Communication Stop Mode

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

Detection Item
Symptom
Trouble Area
ECM Communication Stop Mode
  1. "ECM (Engine)" is not displayed on "Bus Check".
  2. "ECM Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or ECM
  2. ECM main wire or connector
  3. ECM

WIRING DIAGRAM

C158954E10
C158954E11
C180131E01

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)

  1. Disconnect the A52 and C46 ECU connectors.C177488E03

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 2UZ-FE 
    Tester Connection
    Condition
    Specified Condition
    C46-81 (E1) - Body ground
    Always
    Below 1 Ω
    C46-42 (E02) - Body ground
    Always
    Below 1 Ω
    C46-43 (E01) - Body ground
    Always
    Below 1 Ω
    C46-82 (ME01) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 2UZ-FE 
    Tester Connection
    Condition
    Specified Condition
    A52-1 (BATT) - Body ground
    Always
    11 to 14 V
    A52-2 (+B2) - Body ground
    Battery positive (+) voltage applied to terminal MREL
    11 to 14 V
    A52-3 (+B) - Body ground
    Battery positive (+) voltage applied to terminal MREL
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE 
    Tester Connection
    Condition
    Specified Condition
    C46-81 (E1) - Body ground
    Always
    Below 1 Ω
    C46-21 (E02) - Body ground
    Always
    Below 1 Ω
    C46-22 (E01) - Body ground
    Always
    Below 1 Ω
    C46-20 (ME01) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 1GR-FE 
    Tester Connection
    Condition
    Specified Condition
    A52-20 (BATT) - Body ground
    Always
    11 to 14 V
    A52-1 (+B2) - Body ground
    Battery positive (+) voltage applied to terminal MREL
    11 to 14 V
    A52-2 (+B) - Body ground
    Battery positive (+) voltage applied to terminal MREL
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1VD-FTV 
    Tester Connection
    Condition
    Specified Condition
    C46-81 (E1) - Body ground
    Always
    Below 1 Ω
    C46-21 (E02) - Body ground
    Always
    Below 1 Ω
    C46-22 (E01) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 1VD-FTV 
    Tester Connection
    Condition
    Specified Condition
    A52-20 (BATT) - Body ground
    Always
    11 to 14 V
    A52-44 (MREL) - Body ground
    Ignition switch ON
    11 to 14 V
    A52-2 (+B) - Body ground
    Battery positive (+) voltage applied to terminal MREL
    11 to 14 V

Result 
Result
Proceed to
OK (for 2UZ-FE)
A
OK (for 1GR-FE)
B
OK (for 1VD-FTV)
C
NG
D


B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE ECM (Click here)


← Gateway ECU Communication Stop Mode (from Jan 2012)ECM Communication Stop Mode (from Jan 2012) →