2011-2013 Land Cruiser · Service Manual Power Source / Network

Main Body ECU Communication Stop Mode

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

Detection Item
Symptom
Trouble Area
Main Body ECU Communication Stop Mode
Either condition is met:
  1. "Main Body" is not displayed on the "Bus Check" screen.
  2. "Main Body ECU Communication Stop Mode" in "DTC Communication Table" applies.
  1. Power source or inside main body ECU (cowl side junction block LH)
  2. Main body ECU (cowl side junction block LH) CAN branch wire or connector
  3. Main body ECU (cowl side junction block LH)

WIRING DIAGRAM

C175124E03

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3. CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU CAN BRANCH WIRE)

  1. E186831E04
    Disconnect the E3 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E3-5 (CANH) - E3-6 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Main Body ECU [Cowl Side Junction Block LH])



NG
REPAIR OR REPLACE MAIN BODY ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


4. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)

  1. Connect the cable to the negative (-) battery terminal.C259517E01

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Main Body ECU [Cowl Side Junction Block LH])
    *b
    Rear view of wire harness connector
    (to Main Body ECU [Cowl Side Junction Block LH])

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the E3, 2A and 2D main body ECU (cowl side junction block LH) connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    2A-1 (ALTB) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2D-62 (GND2) - Body ground
    Always
    Below 1 Ω
    E3-1 (GND3) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


← Main Body ECU Communication Stop Mode (Sep 2011 – Dec 2011)Combination Meter ECU Communication Stop Mode (Sep 2011 – Dec 2011) →