2011-2013 Land Cruiser · Service Manual Vehicle Interior

B2793 Transponder Chip Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

  1. DTC B2793 is stored when a malfunction is found in the key during key code registration or a key code is not registered normally. Replace the key if key code registration cannot be performed normally and this DTC is output.
  2. DTC B2794 is stored when a key with an incomplete key code is inserted into the ignition key cylinder.
  3. DTC B2797 is stored when a key with a Bcc malfunction is inserted into the ignition key cylinder.
  4. DTC B2798 is stored when a key is inserted into the ignition key cylinder but a communication error occurs between the key and transponder key ECU assembly.
DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2793
A transponder chip malfunction (1 trip detection logic*).
  1. Key
  2. Harness or connector
  3. Transponder key amplifier
  4. Transponder key ECU assembly
Insert the key into the ignition key cylinder.
B2794
A key with an incomplete key code is inserted into the ignition key cylinder (1 trip detection logic*).
B2797
A key with a Bcc malfunction is inserted into the ignition key cylinder (1 trip detection logic*).
B2798
Key code identification cannot be completed within the specified time (1 trip detection logic*).
  1. *: Only output while a malfunction is present.
Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation When Malfunction Detected
Engine cannot be started
-
Related Data List and Active Test 
DTC Code
Data List and Active Test
B2793
Abnormal Status
B2794
Different Encrypt Code
B2797
Bcc Malfunction
B2798
Frame Error

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the key and transponder key ECU assembly, refer to the Service Bulletin.
  2. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Insert and remove each registered key one at a time, and check for DTCs each time (Click here).

    HINT:
    1. Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
    2. If a DTC is output, clear the DTCs before checking the next key.

    OK:
    DTCs B2793, B2974, B2797 and B2798 are not output.

    Result 
    Result
    Proceed to
    OK
    A
    NG (all keys)
    B
    NG (any key)
    C



B
Go to step 3

C
REPLACE KEY THAT CANNOT START ENGINE
A

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK CONNECTION OF CONNECTOR
  1. Check that the connectors are properly connected to the transponder key amplifier.

  1. Check that the engine starts with the key.

    OK:
    Engine starts.



NG
Go to step 4
OK

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

4. REPLACE TRANSPONDER KEY AMPLIFIER
  1. Clear the DTCs. (Click here).

  1. Replace the transponder key amplifier (Click here).

  1. Check that the engine starts with the key.

    OK:
    Engine starts.



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK

END (TRANSPONDER KEY AMPLIFIER WAS DEFECTIVE)


← B2784 Antenna Coil Open / Short (from Jan 2012)B2793 Transponder Chip Malfunction (+ B2794, B2797, B2798) (from Jan 2012) →