2011-2013 Land Cruiser · Service Manual Vehicle Interior

B2799 Engine Immobiliser System Malfunction

Diagnostic trouble codes · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This DTC is stored when one of the following occurs: 1) the ECM detects errors in its own communications with the transponder key ECU assembly; 2) the ECM detects errors in the communication lines; or 3) the ECU - ECM communication ID between the transponder key ECU assembly and ECM is different and an engine start is attempted. Before troubleshooting for this DTC, make sure no engine immobiliser DTCs are output. If output, troubleshoot the engine immobiliser DTCs first.
DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2799
Either condition is met (1 trip detection logic*3):
  1. A malfunction occurs in the communication or communication lines between the ECM and transponder key ECU assembly.
  2. A communication code cannot be verified during communication between the ECM and transponder key ECU assembly.
  1. Harness or connector
  2. Transponder key ECU assembly
  3. ECM
Either condition is met:
  1. Within 10 seconds of an engine start operation being performed an engine start operation refers to turning the ignition switch to ON with the shift lever in P and the brake pedal depressed*1, or the shift lever in N and the brake pedal and clutch pedal depressed*2. If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).
  2. 10 seconds after the ignition switch is turned to ON after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the ignition switch being turned to ON, and DTCs are stored after 6 seconds).
  1. *1: for Automatic Transmission
  2. *2: for Manual Transmission
  1. *3: Only output while a malfunction is present.
Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started
-
Related Data List and Active Test 
DTC Code
Data List and Active Test
B2799
-

WIRING DIAGRAM

B255097E11

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the transponder key ECU assembly, refer to the Service Bulletin.
  2. When replacing the ECM, refer to Initialization (Click here).
  3. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Start the engine.

  1. Wait 10 seconds or more.

  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2799 is not output.

    Result 
    Result
    Proceed to
    OK
    A
    NG (DTC B2799 is output)
    B
    NG (Other DTCs are output)
    C



B
Go to step 3

C
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

3. INSPECT ECM (TERMINAL IMO)

  1. Using an oscilloscope, check the waveform.B288678E03

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Component with harness connected
    (ECM)
    *b
    Waveform
    Measurement Condition 
    Item
    Content
    Tester Connection
    A38-10 (IMO) - Body ground*1
    A52-10 (IMO) - Body ground*2
    Tool Setting
    2 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected
    1. *1: for LHD
    2. *2: for RHD

    HINT:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    OK:
    Waveform is output normally (refer to illustration).

    Result 
    Result
    Proceed to
    Normal waveform
    A
    Terminal IMO stuck low (2.4 V or less)
    B
    Terminal IMO stuck high (12 V) or abnormal waveform
    C



B
Go to step 7

C
Go to step 13
A


4. INSPECT ECM (TERMINAL IMI)

  1. Using an oscilloscope, check the waveform.B288679E02

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Component with harness connected
    (ECM)
    *b
    Waveform
    Measurement Condition 
    Item
    Content
    Tester Connection
    A38-11 (IMI) - Body ground*1
    A52-11 (IMI) - Body ground*2
    Tool Setting
    2 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected
    1. *1: for LHD
    2. *2: for RHD

    HINT:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    OK:
    Waveform is output normally (refer to illustration).

    Result 
    Result
    Proceed to
    Normal waveform
    A
    Not output waveform or abnormal waveform
    B



B
Go to step 9
A


5. REGISTER ECU COMMUNICATION ID
  1. Reregister the ECU communication ID (refer to the Service Bulletin).


NEXT


6. CHECK WHETHER ENGINE STARTS
  1. Check that the engine starts with an already registered vehicle key.

    OK:
    Engine starts normally.



NG
Go to step 13
OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

7. INSPECT ECM (IMO TERMINAL VOLTAGE)

  1. A200912E19
    Disconnect the A38*1 or A52*2 ECM connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to ECM)
    Result 
    Result
    Proceed to
    Terminal IMO stuck low (2.4 V or less)
    A
    Terminal IMO stuck high (12 V)
    B



B
Go to step 13
A


8. CHECK HARNESS AND CONNECTOR (ECM - TRANSPONDER KEY ECU AND BODY GROUND)
  1. Disconnect the E96 transponder key ECU assembly connector.

  1. Disconnect the A38*1 or A52*2 ECM connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    E96-12 (EFII) - A38-10 (IMO)
    Always
    Below 1 Ω
    F96-12 (EFII) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    E96-12 (EFII) - A52-10 (IMO)
    Always
    Below 1 Ω
    E96-12 (EFII) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Replace the transponder key ECU assembly (refer to the Service Bulletin).


NEXT


10. REGISTER KEY
  1. Reregister the key (refer to the Service Bulletin).


NEXT


11. REGISTER ECU COMMUNICATION ID
  1. Reregister the ECU communication ID (refer to the Service Bulletin).


NEXT


12. CHECK WHETHER ENGINE STARTS
  1. Check that the engine starts with an already registered vehicle key.

    OK:
    Engine starts normally.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 1VD-FTV)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

END (TRANSPONDER KEY ECU WAS DEFECTIVE)

13. REPLACE ECM
  1. Temporarily replace the ECM with a new one.

    HINT:
    1. for 1GR-FE (Click here).
    2. for 1VD-FTV (Click here).


NEXT


14. REGISTER ECU COMMUNICATION ID
  1. Reregister the ECU communication ID (refer to the Service Bulletin).


NEXT


15. CHECK WHETHER ENGINE STARTS
  1. Check that the engine starts with the key.

    OK:
    Engine starts normally.



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK

END (ECM WAS DEFECTIVE)


← B2799 Engine Immobiliser System Malfunction (Sep 2011 – Dec 2011)B279A Theft Deterrent System Communication Line High Fixation (Sep 2011 – Dec 2011) →