2011-2013 Land Cruiser · Service Manual Vehicle Interior

B279A Theft Deterrent System Communication Line High Fixation

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When the communication line (IMI - EFIO) between the ECM and transponder key ECU assembly is stuck on HI output, the ECM stores this DTC.
DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B279A
The communication line (IMI - EFIO) between the ECM and transponder key ECU assembly is stuck on HI output (1 trip detection logic*).
  1. Harness or connector
  2. Transponder key ECU assembly
  3. ECM
Turn the ignition switch to ON and wait 6 seconds.
  1. *: Only output while a malfunction is present.
Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops)
Engine start is prohibited
Related Data List and Active Test 
DTC Code
Data List and Active Test
B279A
-

WIRING DIAGRAM

B288680E05

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the transponder key ECU assembly, refer to the Service Bulletin.
  2. When replacing the ECM, refer to Initialization (Click here).
  3. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B279A is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK CONNECTION OF CONNECTOR
  1. Check that the connectors are properly connected to the ECM and transponder key amplifier assembly.

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


4. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
  1. Disconnect the E96 transponder key ECU assembly connector.

  1. Disconnect the A38*1 or A52*2 ECM connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    E96-13 (EFIO) - A38-11 (IMI)
    Always
    Below 1 Ω
    E96-13 (EFIO) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    E96-13 (EFIO) - A52-11 (IMI)
    Always
    Below 1 Ω
    E96-13 (EFIO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Replace the transponder key ECU assembly.


NEXT


6. REGISTER KEY
  1. Register the key (refer to the Service Bulletin).


NEXT


7. REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID (refer to the Service Bulletin).


NEXT


8. CHECK WHETHER ENGINE STARTS
  1. Check that the engine starts with the key.

    OK:
    Engine starts normally.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 1VD-FTV)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

END (TRANSPONDER KEY ECU WAS DEFECTIVE)


← B2799 Engine Immobiliser System Malfunction (from Jan 2012)B279A Theft Deterrent System Communication Line High Fixation (from Jan 2012) →