2011-2013 Land Cruiser · Service Manual Vehicle Interior

INSPECTION

Inspection · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


INSPECT BACK DOOR LOCK ASSEMBLY (w/o Power Back Door)

B183291E03
Text in Illustration 
*1
Full-latch
*2
Open-latch
*a
Component without harness connected
(Back Door Lock assembly)
-
-
  1. Set the back door lock to the full-latch position.

  1. Apply battery voltage to the door motor connector and check the operation of the door lock motor.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 2 (ACT+)
    Battery negative (-) → 1 (ACT-)
    Moves to open-latch position

    1. If the result is not as specified, replace the back door lock assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (ACT-) - 3 (+)
    Open-latch
    Below 1 Ω
    1 (ACT-) - 3 (+)
    Full-latch
    10 kΩ or higher

    1. If the result is not as specified, replace the back door lock assembly.


INSPECT BACK DOOR LOCK ASSEMBLY (w/ Power Back Door)

  1. B300755E01
    Inspect the closer motor operation.

    1. Set the back door lock assembly to the full-latch position.

    2. Apply battery voltage and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 1 (M+)
      Battery negative (-) → 2 (M-)
      Moves to open-latch position

      1. If the result is not as specified, replace the back door lock assembly.

    3. Set the back door lock assembly to the half-latch position.

    4. Apply battery voltage and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2 (M-)
      Battery negative (-) → 1 (M+)
      Moves to over-latch position

      1. If the result is not as specified, replace the back door lock assembly.
        Text in Illustration 
        *1
        Release
        *2
        Close
        *3
        Drive Gear
        *4
        Over-latch
        *5
        Full-latch
        *6
        Half-latch
        *7
        Open-latch
        *a
        Component without harness connected
        (Back Door Lock Assembly)

  1. B300756E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Half-latch Switch 
    Tester Connection
    Condition
    Specified Condition
    5 (CLS) - 4 (E)
    Over-latch
    Below 1 Ω
    Full-latch
    10 kΩ or higher
    Half-latch
    10 kΩ or higher
    Open-latch
    Below 1 Ω

    1. If the result is not as specified, replace the back door lock assembly.

      Closer Position Switch:
      Tester Connection
      Condition
      Specified Condition
      6 (OPN) - 4 (E)
      Selector gear is in center position
      Below 1 Ω
      Selector gear is not in center position
      10 kΩ or higher

    1. If the result is not as specified, replace the back door lock assembly.

    Back Door Courtesy Switch:
    Tester Connection
    Condition
    Specified Condition
    3 (CTY) - 4 (E)
    Half-latch
    Open-latch
    Below 1 Ω
    Over-latch
    Full-latch
    10 kΩ or higher

    1. If the result is not as specified, replace the back door lock assembly.
      Text in Illustration 
      *1
      Release
      *2
      Close
      *3
      Closer Position Switch
      *4
      Selector Gear
      *5
      Drive Gear
      *6
      Over-latch
      *7
      Full-latch
      *8
      Half-latch
      *9
      Open-latch
      *a
      Component without harness connected
      (Back Door Lock Assembly)

← INSPECTION (Sep 2011 – Dec 2011)INSTALLATION (Sep 2011 – Dec 2011) →