2011-2013 Land Cruiser · Service Manual Power Source / Network

Open in One Side of CAN Branch Line

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the intelligent tester "Bus Check" screen, one side of the CAN branch wire may be open (One side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open).
Symptom
Trouble Area
2 or more ECUs and/or sensors do not appear on the intelligent tester "Bus Check" screen.
  1. One side of CAN branch wire is open
  2. Display and navigation module display*1
  3. Center airbag sensor assembly*2
  4. Air conditioning amplifier assembly
  5. Main body ECU (cowl side junction block LH)
  6. Network gateway ECU

HINT:
*1: w/ Navigation System
*2: w/ Airbag System


WIRING DIAGRAM

C176035E03
C176036E06

INSPECTION PROCEDURE

HINT:
  1. Perform the following inspection for the ECUs (sensors) which are not displayed on the intelligent tester. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.
  2. Do not remove the combination meter and ECM, as they are the end parts of the circuit. If removed, CAN communication will not be possible.
  3. The open circuit confirmation of the combination meter, ECM and main wire is performed in the Check CAN Bus Line procedure of How to Proceed with Troubleshooting. This inspection only has procedures for checking for an open circuit on one side of the CAN branch wire.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (DISPLAY AND NAVIGATION MODULE DISPLAY)

NOTICE:
For vehicles without the navigation system, go to "Check for Open in One Side of Branch Wire (Center Airbag Sensor)".

  1. Disconnect the F64 display and navigation module display connector.

  1. Select "Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Display and Navigation (AVN)" not displayed on intelligent tester.
    A
    Several ECUs and sensors other than "Display and Navigation (AVN)" not displayed on intelligent tester.
    B



B
Go to step 4
A


3. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (DISPLAY AND NAVIGATION MODULE DISPLAY BRANCH WIRE)

  1. E191884E10
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F64-21 (CANH) - F64-22 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Display and Navigation Module Display)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (DISPLAY AND NAVIGATION MODULE DISPLAY)
OK

REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY (Click here)

4. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (CENTER AIRBAG SENSOR)

NOTICE:
For vehicles without the airbag system, go to "Check for Open in One Side of Branch Wire (Air Conditioning Amplifier)".

  1. Disconnect the E47 center airbag sensor connector.

  1. Select "Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Airbag" not displayed on intelligent tester.
    A
    Several ECUs and sensors other than "Airbag" not displayed on intelligent tester.
    B



B
Go to step 6
A


5. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (CENTER AIRBAG SENSOR BRANCH WIRE)

  1. E191915E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E47-13 (CANH) - E47-22 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Center Airbag Sensor)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CENTER AIRBAG SENSOR)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

6. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (AIR CONDITIONING AMPLIFIER)
  1. Disconnect the E35*1 or E81*2 air conditioning amplifier connector.

    HINT:
    *1: w/ Rear Air Conditioning System
    *2: w/o Rear Air Conditioning System

  1. Select "Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Air Conditioning Amplifier" not displayed on intelligent tester.
    A
    Several ECUs and sensors other than "Air Conditioning Amplifier" not displayed on intelligent tester.
    B



B
Go to step 8
A


7. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (AIR CONDITIONING AMPLIFIER BRANCH WIRE)

  1. E191927E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ Rear Air Conditioning System 
    Tester Connection
    Switch Condition
    Specified Condition
    E35-3 (CANH) - E35-4 (CANL)
    Ignition switch off
    54 to 69 Ω
    w/o Rear Air Conditioning System 
    Tester Connection
    Switch Condition
    Specified Condition
    E81-11 (CANH) - E81-12 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *A
    w/ Rear Air Conditioning System
    *B
    w/o Rear Air Conditioning System
    *1
    Front view of wire harness connector
    (to Air Conditioning Amplifier)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

8. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (MAIN BODY ECU)
  1. Disconnect the E3 main body ECU (cowl side junction block LH) connector.

  1. Select "Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Main Body" not displayed on intelligent tester.
    A
    Several ECUs and sensors other than "Main Body" not displayed on intelligent tester.
    B



B
Go to step 10
A


9. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (MAIN BODY ECU BRANCH WIRE)

  1. E186831E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E3-5 (CANH) - E3-6 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Main Body ECU)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU

10. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (NETWORK GATEWAY ECU BRANCH WIRE)
  1. Disconnect the E31 network gateway ECU connector.

  1. E191913E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E31-16 (CA1H) - E31-15 (CA1L)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Network Gateway ECU)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (NETWORK GATEWAY ECU)
OK

REPLACE NETWORK GATEWAY ECU (Click here)


← Short to GND in CAN Bus Line (from Jan 2012)Open in One Side of CAN Branch Line (from Jan 2012) →