2011-2013 Land Cruiser · Service Manual Power Source / Network

Open in One Side of CAN Branch Line

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the intelligent tester "Bus Check" screen, one side of the CAN branch wire may be open (One side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open).
Symptom
Trouble Area
2 or more ECUs and/or sensors do not appear on the intelligent tester "Bus Check" screen.
  1. One side of CAN branch wire is open
  2. Center airbag sensor assembly*1
  3. Headlight swivel ECU assembly*2
  4. Multi-media module receiver assembly*3
  5. Air conditioning amplifier assembly
  6. Network gateway ECU
  7. Main body ECU (cowl side junction block LH)
  1. *1: w/ Airbag System
  2. *2: w/ Dynamic Headlight Auto Leveling
  3. *3: w/ Navigation System

WIRING DIAGRAM

C260052E01
C260053E01

INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

HINT:
  1. Perform the following inspection for the ECUs (sensors) which are displayed on the intelligent tester. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.
  2. Do not remove the combination meter and ECM, as they are the end parts of the circuit. If removed, CAN communication will not be possible.
  3. The open circuit confirmation of the combination meter, ECM and main wire is performed in the Check CAN Bus Line procedure of How to Proceed with Troubleshooting. This inspection only has procedures for checking for an open circuit on one side of the CAN branch wire.


1. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MULTI-MEDIA MODULE RECEIVER ASSEMBLY)

NOTICE:
For vehicles without an navigation system, go to "Check for Open in One Side of CAN Branch Wire (Center Airbag Sensor Assembly)".

  1. Disconnect the F77 multi-media module receiver assembly connector.

  1. Select "Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Display and Navigation (AVN)" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Display and Navigation (AVN)" are displayed on the intelligent tester
    B



B
Go to step 3
A


2. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MULTI-MEDIA MODULE RECEIVER ASSEMBLY CAN BRANCH WIRE)

  1. C250794E10
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F77-1 (CANH) - F77-2 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Multi-media Module Receiver Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY)
OK

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)

3. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY)

NOTICE:
For vehicles without the airbag system, go to "Check for Open in One Side of Branch Wire (Air Conditioning Amplifier)".

  1. Disconnect the E47 center airbag sensor assembly connector.

  1. Select "Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "" are displayed on the intelligent tester
    B



B
Go to step 5
A


4. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)

  1. C222818E15
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E47-13 (CANH) - E47-22 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Center Airbag Sensor Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

5. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
  1. Disconnect the E35*1 or E81*2 air conditioning amplifier assembly connector.

    1. *1: w/ Rear Air Conditioning System
    2. *2: w/o Rear Air Conditioning System

  1. Select "Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Air Conditioning Amplifier" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Air Conditioning Amplifier" are displayed on the intelligent tester
    B



B
Go to step 7
A


6. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)

  1. E191927E02
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ Rear Air Conditioning System 
    Tester Connection
    Switch Condition
    Specified Condition
    E35-3 (CANH) - E35-4 (CANL)
    Ignition switch off
    54 to 69 Ω
    w/o Rear Air Conditioning System 
    Tester Connection
    Switch Condition
    Specified Condition
    E81-11 (CANH) - E81-12 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *A
    w/ Rear Air Conditioning System
    *B
    w/o Rear Air Conditioning System
    *a
    Front view of wire harness connector
    (to Air Conditioning Amplifier Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

7. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (HEADLIGHT SWIVEL ECU ASSEMBLY)

NOTICE:
For vehicles without an dynamic headlight auto leveling, go to "Check for Open in One Side of CAN Branch Wire (Main Body ECU)".

  1. Disconnect the E101 headlight swivel ECU assembly connector.

  1. Select "Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Headlight swivel (AFS)" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Headlight swivel (AFS)" are displayed on the intelligent tester
    B



B
Go to step 9
A


8. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (HEADLIGHT SWIVEL ECU ASSEMBLY CAN BRANCH WIRE)

  1. C240252E05
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E101-12 (MPX1) - E101- 13 (MPX2)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Headlight Swivel ECU Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY)
OK

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (Click here)

9. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU)
  1. Disconnect the E3 main body ECU (cowl side junction block LH) connector.

  1. Select "Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Main Body" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Main Body" are displayed on the intelligent tester
    B



B
Go to step 11
A


10. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU CAN BRANCH WIRE)

  1. E186831E04
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E3-5 (CANH) - E3-6 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Main Body ECU [Cowl Side Junction Block LH])



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

11. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NETWORK GATEWAY ECU CAN BRANCH WIRE)

  1. C242749E10
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the E31 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E31-16 (CA1H) - E31-15 (CA1L)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Network Gateway ECU)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (NETWORK GATEWAY ECU)
OK

REPLACE NETWORK GATEWAY ECU (Click here)


← Open in One Side of CAN Branch Line (Sep 2011 – Dec 2011)COMPONENTS (from Sep 2011) →