2011-2013 Land Cruiser · Service Manual Vehicle Interior

Back Door Entry Lock Function does not Operate

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

If the back door entry lock function does not operate but the back door open function operates, the communication line between the vehicle and electrical key transmitter is normal. The part at fault may be the entry lock switch circuit (certification ECU (smart key ECU assembly) → back door opener switch).

WIRING DIAGRAM

B194360E02
B187333E05

INSPECTION PROCEDURE

NOTICE:
Before performing the inspection, check that there are no problems related to the "CAN Communication System" and "LIN Communication System".


1. CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch of the master switch assembly is operated, check that the locked doors unlock.

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2. CHECK VEHICLE EQUIPMENT
  1. Check if the power back door is equipped on the vehicle.

    Result 
    Result
    Proceed to
    w/ Power Back Door System
    A
    w/o Power Back Door System
    B



B
Go to step 4
A


3. CHECK POWER BACK DOOR OPERATION
  1. When the power back door switch is operated, check that the power back door closes.

    OK:
    Power back door system is normal.

    Result 
    Result
    Proceed to
    Power back door system is abnormal
    A
    Power back door system is normal
    B



B
Go to step 5
A

GO TO POWER BACK DOOR SYSTEM (Click here)

4. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    Back Lock Pos switch
    Back door lock position switch signal / ON or OFF
    ON: Back door is unlocked
    OFF: Back door is locked
    -

    OK:
    On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Back Door LOCK/UNLOCK Functions do not Operate) (Click here)
OK


5. READ VALUE USING INTELLIGENT TESTER (BACK DOOR LOCK SWITCH)
  1. Using the intelligent tester, read the Data List.

    Entry&Start 
    Tester Display
    Measurement Item/Display
    Normal Condition
    Diagnostic Note
    Tr/B-Door Lock SW
    Back door lock switch / ON or OFF
    ON: Back door lock switch is pushed
    OFF: Back door lock switch is not pushed
    -

    OK:
    "ON" (switch is pushed) and "OFF" (switch is not pushed) appears on the screen.



NG
Go to step 6
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

6. CHECK BACK DOOR OPENER SWITCH

  1. B185531E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (UL) - 2 (L)
    Lock switch pushed
    Below 1 Ω
    1 (UL) - 2 (L)
    Lock switch not pushed
    10 kΩ or higher



NG
REPLACE BACK DOOR OPENER SWITCH (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - BACK DOOR OPENER SWITCH)

  1. B171361E03
    Disconnect the E29 ECU connector.

  1. Disconnect the S7 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E29-7 (TSW5) - S7-1 (UL)
    Always
    Below 1 Ω
    E29-7 (TSW5) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


← Back Door Entry Lock Function does not Operate (Sep 2011 – Dec 2011)PRECAUTION (Sep 2011 – Dec 2011) →