2011-2013 Land Cruiser · Service Manual Vehicle Interior

Back Door Entry Lock and Unlock Functions do not Operate

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When the back door entry lock and unlock functions do not operate, one of the following may be malfunctioning: 1) power door lock control system, or 2) back door electrical key antenna (for outer), or 3) main body ECU (cowl side junction block LH), or 4) certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B187333E01

INSPECTION PROCEDURE

NOTICE:
Before performing the inspection, check that there are no problems related to "CAN COMMUNICATION SYSTEM" and "LIN COMMUNICATION SYSTEM".


1. CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch of the master switch assembly is operated, check that the locked doors unlock.

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Lock Pos switch
    Back door lock position switch signal / ON or OFF
    ON: Back door is unlocked
    OFF: Back door is locked
    -

    OK:
    On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Back Door LOCK/UNLOCK Functions do not Operate) (Click here)
OK


3. READ VALUE USING INTELLIGENT TESTER (BACK DOOR LOCK SWITCH, BACK DOOR OPENER SWITCH)
  1. Using the intelligent tester, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Door Handle SW
    Back door opener switch / ON or OFF
    ON: Back door opener switch is pushed
    OFF: Back door opener switch is not pushed
    -
    Entry & Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Tr/B-Door Lock SW
    Back door lock switch / ON or OFF
    ON: Back door lock switch is pushed
    OFF: Back door lock switch is not pushed
    -

    OK:
    "ON" (switch is pushed) or "OFF" (switch is not pushed) appears on the screen.



NG
Go to step 7
OK


4. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - BACK DOOR ELECTRICAL KEY ANTENNA [for Outer])

  1. B108064E08
    Disconnect the E29 ECU connector.

  1. Disconnect the K23 antenna connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E29-31 (CLG8) - K23-1 (CLG5)
    Always
    Below 1 Ω
    E29-32 (CG8B) - K23-2 (CLGB)
    Always
    Below 1 Ω
    E29-31 (CLG8) - Body ground
    Always
    10 kΩ or higher
    E29-32 (CG8B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE BACK DOOR ELECTRICAL KEY ANTENNA (for Outer)
  1. Replace the back door electrical key antenna (Click here).


NEXT


6. CHECK BACK DOOR ELECTRICAL KEY ANTENNA [for Outer] (OPERATION)
  1. Check that the entry functions operate normally.

    OK:
    Entry functions operate normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (BACK DOOR ELECTRICAL KEY ANTENNA IS DEFECTIVE)

7. CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH - BODY GROUND)

  1. B156829E01
    Disconnect the S7 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S7-2 (L) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK DOOR OPENER SWITCH (Click here)


← Back Door Entry Unlock Function does not Operate (from Jan 2012)Back Door Entry Lock and Unlock Functions do not Operate (from Jan 2012) →