2011-2013 Land Cruiser · Service Manual Brake

TEST MODE PROCEDURE

Troubleshooting · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


TEST MODE (SIGNAL CHECK) PROCEDURE (SST CHECK WIRE)

HINT:
  1. After replacing the master cylinder solenoid and/or G sensor, make sure to perform G sensor zero point calibration (Click here).
  2. If the ignition switch is turned from ON to ACC or off during test mode (signal check), DTCs of the signal check function will be cleared.
  3. During test mode (signal check), the skid control ECU stores all DTCs of the test mode (signal check) function. By performing the test mode (signal check), the codes are cleared if normality is confirmed. The codes left over are the codes where an abnormality was found.

  1. Turn the ignition switch off.

  2. Check that the steering wheel is centered.

  3. for A/T:
    Move the shift lever to P.

  4. for M/T:
    Pull the parking brake lever.

  5. C166029E02
    Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
    SST
    09843-18040  

  6. Turn the ignition switch to ON.

  7. C173109E02
    Check that the ABS warning light blinks in test mode.

    HINT:
    1. If the G sensor zero point calibration data is cleared, the ABS warning light comes on.
    2. If the G sensor zero point calibration data is not cleared and the ABS warning light does not blink, inspect the 12 (TS) and 4 (CG) terminal circuit and the ABS warning light circuit.
      Trouble Area
      See Procedure
      TS and CG terminal circuit
      Click here
      ABS warning light circuit
      Click here or Click here

  8. Start the engine.

  9. Using a check wire, perform the ABS sensor (G sensor, master cylinder pressure sensor, center differential lock detection switch and speed sensor) signal checks in test mode.


G SENSOR SIGNAL CHECK (SST CHECK WIRE) (Procedure "A")

  1. C173109E02
    Check that the ABS warning light is blinking in test mode.

  2. Keep the vehicle stationary on a level surface for 2 seconds or more.


MASTER CYLINDER PRESSURE SENSOR SIGNAL CHECK (SST CHECK WIRE) (Procedure "B")

  1. C173109E02
    Check that the ABS warning light is blinking in test mode.

  2. Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and then quickly depress the brake pedal with a force of 98 N (10 kgf, 22.0 lbf) or more for 1 second or more.

    HINT:
    1. At this time, the ABS warning light stays on for 3 seconds.
    2. The ABS warning light comes on for 3 seconds every time the brake pedal operation above is performed.


CENTER DIFFERENTIAL LOCK DETECTION SWITCH SIGNAL CHECK (SST CHECK WIRE) (Procedure "C")

  1. C173109E02
    Check that the ABS warning light is blinking in test mode.

  2. Check the center differential lock switch.

    1. Push the center differential lock switch on to lock the center differential.

    2. Push the center differential lock switch off to unlock the center differential.


SPEED SENSOR SIGNAL CHECK (SST CHECK WIRE) (Procedure "D")

  1. C173109E02
    Check that the ABS warning light is blinking in test mode.

  2. Check the reverse signal.

    1. Drive the vehicle in reverse for more than 1 second at 3 km/h (2 mph) or more.

      HINT:
      Drive the vehicle in reverse and check the speed sensor signal. Note that the signal check cannot be completed if the vehicle speed is 45 km/h (28 mph) or more.

  3. Check the forward signal.
    C162681E01

    1. Drive the vehicle straight forward.
      Drive the vehicle at a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.

      NOTICE:
      The signal check may not be completed if the vehicle has its wheels spun or the steering wheel is turned during this check.

  4. Stop the vehicle.

    NOTICE:
    1. The speed sensor signal check may not be completed if the speed sensor signal check is started while turning the steering wheel or spinning the wheels.
    2. If the signal check has not been completed, the ABS warning light blinks while driving and the ABS system does not operate.

    HINT:
    When the signal check has been completed, the ABS warning light goes off while driving and blinks in the test mode pattern while stationary.


READ DTC OF ABS SENSOR (SST CHECK WIRE) (Procedure "E")

  1. C166029E04
    Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
    SST
    09843-18040  

  2. Read the number of blinks of the ABS warning light.

    HINT:
    1. See the list of DTCs (See procedure "F").
    2. If every sensor is normal, the normal system code is output (a cycle of 0.25 seconds on and 0.25 seconds off is repeated).
    3. If more than 1 malfunction is detected at the same time, the lowest numbered code will be output first.

    C173110E01

  3. After the check, disconnect SST from terminals 13 (TC) and 4 (CG) of the DLC3.


DTC OF SIGNAL CHECK FUNCTION (SST CHECK WIRE) (Procedure "F")
DTC Code
Detection Item
Trouble Area
C1271/71
Front Speed Sensor RH Output Voltage Malfunction
  1. Front speed sensor RH
  2. Sensor installation
  3. Speed sensor rotor
C1272/72
Front Speed Sensor LH Output Voltage Malfunction
  1. Front speed sensor LH
  2. Sensor installation
  3. Speed sensor rotor
C1273/73
Rear Speed Sensor RH Output Voltage Malfunction
  1. Rear speed sensor RH
  2. Sensor installation
  3. Speed sensor rotor
C1274/74
Rear Speed Sensor LH Output Voltage Malfunction
  1. Rear speed sensor LH
  2. Sensor installation
  3. Speed sensor rotor
C1275/75
Abnormal Change in Output Signal of Front Speed Sensor RH
Speed sensor rotor
C1276/76
Abnormal Change in Output Signal of Front Speed Sensor LH
Speed sensor rotor
C1277/77
Abnormal Change in Output Signal of Rear Speed Sensor RH
Speed sensor rotor
C1278/78
Abnormal Change in Output Signal of Rear Speed Sensor LH
Speed sensor rotor
C1279/79
G Sensor Output Voltage Malfunction
  1. G sensor
  2. Sensor installation
C1281/81
Master Cylinder Pressure Sensor Output Malfunction
  1. Stop light switch
  2. Brake pedal load sensing switch
  3. Master cylinder pressure sensor
C1282/82
Center Differential Lock Detection Switch Malfunction
Center differential lock switch

HINT:
The codes in this table are stored only in test mode (signal check).


TEST MODE (SIGNAL CHECK) PROCEDURE (INTELLIGENT TESTER)

HINT:
  1. After replacing the master cylinder solenoid and/or G sensor, make sure to perform G sensor zero point calibration (Click here).
  2. If the ignition switch is turned from ON to ACC or off during test mode (signal check), DTCs of the signal check function will be cleared.
  3. During test mode (signal check), the skid control ECU stores all DTCs of the test mode (signal check) function. By performing the test mode (signal check), the codes are cleared if normality is confirmed. The codes left over are the codes where an abnormality was found.

  1. Turn the ignition switch off.

  2. Check that the steering wheel is centered.

  3. for A/T:
    Move the shift lever to P.

  4. for M/T:
    Pull the parking brake lever.

  5. Connect the intelligent tester to the DLC3.

  6. Turn the ignition switch to ON.

  7. Turn the intelligent tester on.

  8. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.

  9. C173109E02
    Check that the ABS warning light blinks in test mode.

    HINT:
    1. If the G sensor zero point calibration data is cleared, the ABS warning light comes on.
    2. If the G sensor zero point calibration data is not cleared and the ABS warning light does not blink, inspect the 12 (TS) and 4 (CG) terminal circuit and the ABS warning light circuit.
      Trouble Area
      See Procedure
      TS and CG terminal circuit
      Click here
      ABS warning light circuit
      Click here or Click here

  10. Start the engine.

  11. Using the intelligent tester, perform the ABS sensor (G sensor, master cylinder pressure sensor, center differential lock detection switch and speed sensor) signal checks in test mode.


G SENSOR SIGNAL CHECK (INTELLIGENT TESTER) (Procedure "G")

  1. C173109E02
    Check that the ABS warning light is blinking in test mode.

  2. Keep the vehicle stationary on a level surface for 2 seconds or more.


MASTER CYLINDER PRESSURE SENSOR SIGNAL CHECK (INTELLIGENT TESTER) (Procedure "H")

  1. C173109E02
    Check that the ABS warning light is blinking in test mode.

  2. Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and then quickly depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second or more.

    HINT:
    1. At this time, the ABS warning light stays on for 3 seconds.
    2. The ABS warning light comes on for 3 seconds every time the brake pedal operation above is performed.


CENTER DIFFERENTIAL LOCK DETECTION SWITCH SIGNAL CHECK (INTELLIGENT TESTER) (Procedure "I")

  1. C173109E02
    Check that the ABS warning light is blinking in test mode.

  2. Check the center differential lock switch.

    1. Push the center differential lock switch on to lock the center differential.

    2. Push the center differential lock switch off to unlock the center differential.


SPEED SENSOR SIGNAL CHECK (INTELLIGENT TESTER) (Procedure "J")

  1. C173109E02
    Check that the ABS warning light is blinking in test mode.

  2. Check the reverse signal.

    1. Drive the vehicle in reverse for more than 1 second at 3 km/h (2 mph) or more.

      HINT:
      Drive the vehicle in reverse and check the speed sensor signal. Note that the signal check cannot be completed if the vehicle speed is 45 km/h (28 mph) or more.

  3. Check the forward signal.
    C162681E01

    1. Drive the vehicle straight forward. Drive the vehicle at a speed of 45 km/h (28 mph) or more and check that the ABS warning light goes off.

      NOTICE:
      The signal check may not be completed if the vehicle has its wheels spun or the steering wheel is turned during this check.

  4. Stop the vehicle.

    NOTICE:
    1. The speed sensor signal check may not be completed if the speed sensor signal check is started while turning the steering wheel or spinning the wheels.
    2. If the signal check has not been completed, the ABS warning light blinks while driving and the ABS system does not operate.

    HINT:
    When the signal check has been completed, the ABS warning light goes off while driving and blinks in the test mode pattern while stationary.


READ DTC OF ABS SENSOR (INTELLIGENT TESTER) (Procedure "K")
  1. Read the DTC(s) by following the intelligent tester screen.

    HINT:
    1. Refer to the intelligent tester operator's manual for further details.
    2. See the list of DTCs (See procedure "L").


DTC OF SIGNAL CHECK FUNCTION (INTELLIGENT TESTER) (Procedure "L")
DTC Code
Detection Item
Trouble Area
C1271/71
Front Speed Sensor RH Output Voltage Malfunction
  1. Front speed sensor RH
  2. Sensor installation
  3. Speed sensor rotor
C1272/72
Front Speed Sensor LH Output Voltage Malfunction
  1. Front speed sensor LH
  2. Sensor installation
  3. Speed sensor rotor
C1273/73
Rear Speed Sensor RH Output Voltage Malfunction
  1. Rear speed sensor RH
  2. Sensor installation
  3. Speed sensor rotor
C1274/74
Rear Speed Sensor LH Output Voltage Malfunction
  1. Rear speed sensor LH
  2. Sensor installation
  3. Speed sensor rotor
C1275/75
Abnormal Change in Output Signal of Front Speed Sensor RH
Speed sensor rotor
C1276/76
Abnormal Change in Output Signal of Front Speed Sensor LH
Speed sensor rotor
C1277/77
Abnormal Change in Output Signal of Rear Speed Sensor RH
Speed sensor rotor
C1278/78
Abnormal Change in Output Signal of Rear Speed Sensor LH
Speed sensor rotor
C1279/79
G Sensor Output Voltage Malfunction
  1. G sensor
  2. Sensor installation
C1281/81
Master Cylinder Pressure Sensor Output Malfunction
  1. Stop light switch
  2. Brake pedal load sensing switch
  3. Master cylinder pressure sensor
C1282/82
Center Differential Lock Detection Switch Malfunction
Center differential lock switch

HINT:
The codes in this table are stored only in test mode (signal check).

← CALIBRATION (from Jan 2012)TEST MODE PROCEDURE (from Jan 2012) →