2011-2013 Land Cruiser · Service Manual Brake

ABS Warning Light does not Come ON

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

If any of the following is detected, the ABS warning light remains on.
  1. The skid control ECU connectors are disconnected from the skid control ECU.
  2. There is a malfunction in the skid control ECU internal circuit.
  3. There is an open in the harness between the combination meter and skid control ECU.

HINT:
There is a case that the intelligent tester cannot be used when the skid control ECU is abnormal.


WIRING DIAGRAM

C173343E01

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).


1. INSPECT ABS WARNING LIGHT
  1. Disconnect the skid control ECU connector.

  1. Turn the ignition switch to ON.

  1. Check that the ABS warning light comes on.

    OK:
    ABS warning light comes on.

    Result 
    Result
    Proceed to
    NG
    A
    OK
    LHD
    B
    RHD
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A


2. CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and the intelligent tester on.

  1. Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN Bus.

    OK:
    "Bus Check" indicates no malfunctions in CAN communication.

    Result 
    Result
    Proceed to
    OK
    A
    NG
    LHD
    B
    RHD
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


3. CHECK DTC (CAN COMMUNICATION SYSTEM)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and the intelligent tester on.

  1. Check for DTCs (LHD: Click here/RHD: Click here).

    Result 
    Result
    Proceed to
    CAN system DTC is not output
    A
    CAN system DTC is output
    LHD
    B
    RHD
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


4. CHECK OPERATION OF ABS WARNING LIGHT (ACTIVE TEST)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and the intelligent tester on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. Check the condition of the ABS warning light by operating the intelligent tester.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. Lamp ABS
    ABS Warning Light
    Warning light ON/OFF
    -

    OK:
    The warning light turns on when operating the intelligent tester.

    Result 
    Result
    Proceed to
    OK
    A
    NG
    w/ Multi-information Display
    B
    w/o Multi-information Display
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE COMBINATION METER ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← ABS Warning Light Remains ON (from Jan 2012)ABS Warning Light does not Come ON (from Jan 2012) →