2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

HINT:
  1. Although the DTC titles say oxygen sensor, these DTCs relate to the Air Fuel ratio (A/F) sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.

The A/F sensor, which is located between the exhaust manifold and catalyst, consists of alloyed metal elements and a heater.
Depending on the engine operating conditions, the heater heats the sensor elements to activate them. Battery voltage is applied to the heater, and the sensor ground is controlled by the ECM using a duty ratio.
The sensor elements convert the oxygen concentration in the exhaust gas into voltage values to output. Based on the voltage, the ECM determines the air fuel ratio and regulates the fuel injection volume depending on the air fuel ratio and engine operating conditions. The voltage changes between 0.6 V and 4.5 V while the engine is running. If the air fuel ratio is lean, which means the oxygen concentration in the exhaust gas is high, the voltage is high. If the air fuel ratio is rich, which means the oxygen concentration in the exhaust gas is low, the voltage is low.
A160615E01
A178930E02
DTC Code
DTC Detection Condition
Trouble Area
P2237
P2240
An open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while the engine is running (2 trip detection logic).
  1. Open in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. ECM
P2238
P2241
Any of the following conditions are met (2 trip detection logic):
  1. The A/F sensor output drops while the engine is running.
  1. The voltage at terminal A1A+/A2A+ is 0.5 V or less.
  1. The voltage difference between terminals A1A+/A2A+ and A1A-/A2A- is 0.1 V or less.
  1. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. ECM
P2239
P2242
The A1A+/A2A+ voltage is higher than 4.5 V (2 trip detection logic).
  1. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. ECM
P2252
P2255
The A1A-/A2A- voltage is 0.5 V or less (2 trip detection logic).
  1. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. ECM
P2253
P2256
The A1A-/A2A- voltage is higher than 4.5 V (2 trip detection logic).
  1. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. ECM

MONITOR DESCRIPTION

These DTCs are stored when there is an open or short in the A/F sensor circuit, or if A/F sensor output drops. To detect these problems, the voltage of the A/F sensor is monitored when turning the ignition switch to ON, and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the A/F sensor is between 0.6 V and 4.5 V, it is considered normal. If the voltage is out of the specified range, or the admittance is less than the standard value, the ECM will determine that there is a malfunction in the A/F sensor. If the same malfunction is detected in next driving cycle, the MIL will be illuminated and a DTC will be stored.

WIRING DIAGRAM

Refer to DTC P2195 (Click here).

CONFIRMATION DRIVING PATTERN

  1. Start the engine and wait for 5 minutes or more.

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air Fuel ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the tester on.
  3. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. On the tester, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  5. Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
  6. Monitor the output voltages of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
+25%
Rich
less than 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
-12.5%
Lean
more than 3.4 V
O2S B1S2 or O2S B2S2
(HO2)
+25%
Rich
more than 0.55 V
O2S B1S2 or O2S B2S2
(HO2)
-12.5%
Lean
less than 0.4 V

NOTICE:
The Air Fuel ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E05
A150787E01
A150788E03
-
2
A150787E01
A150790E01
A150787E01
A150788E03
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E05
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Injector
  2. Fuel pressure
  3. Gas leakage from exhaust system (air fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)

  1. A182483E01
    Disconnect the Air Fuel ratio (A/F) sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C22-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    C23-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Turn the ignition switch off.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C22-1 (HA1A) - C45-86 (HA1A)
    Always
    Below 1 Ω
    C22-3 (A1A+) - C45-93 (A1A+)
    Always
    Below 1 Ω
    C22-4 (A1A-) - C45-116 (A1A-)
    Always
    Below 1 Ω
    C23-1 (HA2A) - C45-109 (HA2A)
    Always
    Below 1 Ω
    C23-3 (A2A+) - C45-120 (A2A+)
    Always
    Below 1 Ω
    C23-4 (A2A-) - C45-119 (A2A-)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C22-1 (HA1A) - C46-86 (HA1A)
    Always
    Below 1 Ω
    C22-3 (A1A+) - C46-93 (A1A+)
    Always
    Below 1 Ω
    C22-4 (A1A-) - C46-116 (A1A-)
    Always
    Below 1 Ω
    C23-1 (HA2A) - C46-109 (HA2A)
    Always
    Below 1 Ω
    C23-3 (A2A+) - C46-120 (A2A+)
    Always
    Below 1 Ω
    C23-4 (A2A-) - C46-119 (A2A-)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C22-1 (HA1A) or C45-86 (HA1A) - Body ground
    Always
    10 kΩ or higher
    C22-3 (A1A+) or C45-93 (A1A+) - Body ground
    Always
    10 kΩ or higher
    C22-4 (A1A-) or C45-116 (A1A-) - Body ground
    Always
    10 kΩ or higher
    C23-1 (HA2A) or C45-109 (HA2A) - Body ground
    Always
    10 kΩ or higher
    C23-3 (A2A+) or C45-120 (A2A+) - Body ground
    Always
    10 kΩ or higher
    C23-4 (A2A-) or C45-119 (A2A-) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C22-1 (HA1A) or C46-86 (HA1A) - Body ground
    Always
    10 kΩ or higher
    C22-3 (A1A+) or C46-93 (A1A+) - Body ground
    Always
    10 kΩ or higher
    C22-4 (A1A-) or C46-116 (A1A-) - Body ground
    Always
    10 kΩ or higher
    C23-1 (HA2A) or C46-109 (HA2A) - Body ground
    Always
    10 kΩ or higher
    C23-3 (A2A+) or C46-120 (A2A+) - Body ground
    Always
    10 kΩ or higher
    C23-4 (A2A-) or C46-119 (A2A-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


3. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


4. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 5 minutes or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

  1. Read the pending DTCs.

    Result 
    Result
    Proceed to
    No output
    A
    P2237, P2240, P2238, P2241, P2239, P2242, P2252, P2255, P2253 or P2256 output
    B



B
REPLACE ECM (Click here)
A

END


← P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) (+ P2196, P2197, P2198) (from Jan 2012)P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) (+ 9 more codes) (from Jan 2012) →