2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REASSEMBLY

Removal / installation · Vehicles built from Sep 2011

NOTICE:
Before performing these installation procedures, sufficiently clean and remove any foreign matter from the cylinder block, connecting rod and other parts.


1. INSTALL CYLINDER BLOCK STRAIGHT SCREW PLUG

  1. A177329E02
    Install 2 new gaskets and the 2 straight screw plugs.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }


2. INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

  1. A164571
    Using a 5 mm hexagon wrench, install the 4 oil nozzles with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


3. INSTALL PISTON PIN HOLE SNAP RING

  1. A182756E01
    Using a screwdriver, install a new snap ring on one side of the piston pin hole.

    HINT:
    Be sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.


4. INSTALL PISTON WITH PIN SUB-ASSEMBLY

  1. A164822E01
    Gradually heat the piston to approximately 80°C (176°F).

  1. Coat the piston pin with engine oil.

  1. A181687E01
    RH:

    1. Align the front marks of the piston and connecting rod, and push in the piston pin with your thumb.

      HINT:
      1. The piston and pin are a matched set.
      2. The piston has 2 front marks.

  1. A182755E01
    LH:

    1. Face the front marks of the piston and connecting rod in opposite directions, and push in the piston pin with your thumb.

      HINT:
      1. The piston and pin are a matched set.
      2. The piston has 1 front mark.

  1. A164623
    Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.


5. INSTALL PISTON PIN HOLE SNAP RING

  1. A182757E01
    Using a screwdriver, install a new snap ring at the other end of the piston pin hole.

    HINT:
    Be sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.


6. INSTALL PISTON RING SET

  1. A164800
    Install the oil ring expander by hand.

  1. A164625E02
    Using a piston ring expander, install the oil ring.

    HINT:
    Align the oil ring ends and coil joint as shown in the illustration.

  1. A164626E02
    Using a piston ring expander, install the No. 1 and No. 2 compression rings so that the code marks are positioned as shown in the illustration.

    HINT:
    1. w/ EGR System:
      Install the No. 1 compression ring with the code mark shown in the table below facing upward.
    2. w/o EGR System:
      Install the No. 1 compression ring with no code mark. The compression ring can be installed with either side facing upward.
    3. Install the No. 2 compression ring with the code mark shown in the table below facing upward.

    Standard Code Mark:
    Item
    Code Mark
    (w/ EGR System)
    Code Mark
    (w/o EGR System)
    No. 1 compression ring
    1T
    No mark
    No. 2 compression ring
    T2
    2T

  1. A170352E02
    Position the piston rings so that the ring ends are as shown in the illustration.


7. INSTALL CONNECTING ROD BEARING

  1. A164871E02
    Align the bearing claw with the claw groove of the connecting rod cap.

    NOTICE:
    1. Clean the contact surface of the bearing and connecting rod cap.
    2. Do not apply engine oil to the bearing and its contact surface.

  1. Align the bearing claw with the claw groove of the connecting rod.

    NOTICE:
    1. Clean the contact surface of the bearing and connecting rod.
    2. Do not apply engine oil to the bearing and its contact surface.


8. INSTALL CRANKSHAFT BEARING

NOTICE:
Be sure to install the selected bearing.


HINT:
A164627E01
Main bearings come in widths of 20.5 mm (0.807 in.) and 22.5 mm (0.886 in.).

Bearing Width 
Item
Standard Width
No. 1 and 5 journal bearings
22.5 mm (0.886 in.)
No. 2, 3 and 4 journal bearings
20.5 mm (0.807 in.)
  1. Clean each main journal and bearing.

  1. A164628
    Align the bearing claw with the claw groove of the cylinder block, and push in the 5 upper crankshaft bearings.

    NOTICE:
    1. Clean the contact surface of the bearing and cylinder block.
    2. Do not apply engine oil to the bearing and its contact surface.
    3. Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.

  1. A164629
    Align the bearing claw with the claw groove of the bearing cap, and push in the 5 lower crankshaft bearings.

    NOTICE:
    1. Clean the contact surface of the bearing and crankshaft bearing cap.
    2. Do not apply engine oil to the bearing and its contact surface.

    HINT:
    The number marked on each bearing cap indicates the installation position.


9. INSTALL CRANKSHAFT

NOTICE:
Clean the contact surface of each main journal and crank pin.

  1. A164570
    Apply new engine oil to the upper crankshaft bearing and install the crankshaft to the cylinder block.

  1. A164600E02
    Push the crankshaft toward the rear thrust direction to create clearance, and install a thrust washer to the No. 3 journal position with the oil groove facing the front of the engine.

  1. Push the crankshaft toward the forward thrust direction to create clearance, and install a thrust washer to the No. 3 journal position with the oil groove facing the rear of the engine.

  1. A164632E01
    Examine the front marks and numbers and install the bearing caps to the cylinder block.

  1. Apply a light coat of engine oil to the threads of the crankshaft bearing cap bolts.

  1. A170351E01
    Temporarily install the crankshaft bearing cap bolts labeled A or the bolts labeled B.

    HINT:
    In place of the cylinder block stiffening plates, install 8 mm (0.315 in.) thick spacers to the crankshaft bearing cap bolts.
    Standard Length 
    Item
    Diameter
    Length
    A
    11 mm (0.433 in.)
    106 mm (4.17 in.)
    B
    10 mm (0.394 in.)
    90.5 mm (3.56 in.)

  1. Uniformly tighten the 2 crankshaft bearing cap bolts for each bearing cap in several passes to ensure a proper fit.

    NOTICE:
    Do not tap the bearing cap with a plastic-faced hammer.

  1. Remove the crankshaft bearing cap bolts and spacers.

  1. A164799E02
    Set the 2 cylinder block stiffening plates on the cylinder block.

    HINT:
    Make sure the arrows on the stiffening plates face the engine front.

  1. A178516E01
    Step 1:

    HINT:
    1. The crankshaft bearing cap bolts are tightened in 4 progressive steps.
    2. If any crankshaft bearing cap bolt is broken or deformed, replace it.


    1. Apply a light coat of engine oil to the threads and under the heads of the 20 crankshaft bearing cap bolts A and B.

    2. Install the 20 crankshaft bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence shown in the illustration.

      Torque:
      for bolt A:
      35 N*m{ 357 kgf*cm , 26 ft.*lbf }
      for bolt B:
      60 N*m{ 612 kgf*cm , 44 ft.*lbf }

  1. A164901E01
    Step 2:

    1. Mark the front side of the crankshaft bearing cap bolts A and B with paint.

    2. Tighten the crankshaft bearing cap bolts A and B 90° in the sequence shown in the illustration.

  1. A164902E01
    Step 3:

    1. Tighten the crankshaft bearing cap bolts A another 90° in the sequence shown in the illustration.

  1. A170349E02
    Check that the painted marks of bolt A are now at a 180° angle to the front.

  1. A170350E01
    Check that the painted marks of bolt B are now at a 90° angle to the front.

  1. Check that the crankshaft turns smoothly.

  1. A164796E02
    Step 4:

    1. Using several steps, install the 10 crankshaft bearing cap bolts uniformly in the sequence shown in the illustration.

      Torque:
      56 N*m{ 571 kgf*cm , 41 ft.*lbf }

    2. Check that the crankshaft turns smoothly.


10. INSPECT CRANKSHAFT THRUST CLEARANCE

  1. A164572
    Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

    Standard thrust clearance:
    0.02 to 0.22 mm (0.000787 to 0.00866 in.)

    Maximum thrust clearance:
    0.30 mm (0.0118 in.)

    If the thrust clearance is more than the maximum, replace the thrust washers as a set.

    Standard thrust washer thickness:
    2.44 to 2.49 mm (0.0961 to 0.0980 in.)

    If necessary, replace the crankshaft.


11. INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

  1. A170352E02
    Apply engine oil to the cylinder walls, pistons, and the surfaces of the connecting rod bearings.

  1. Check the positions of the piston ring ends.

  1. A181667E01
    Using a hammer handle and piston ring compressor, press a piston and connecting rod assembly into each cylinder with the front mark of the piston facing forward.

  1. A164639E02
    Install the connecting rod cap so that its protrusion is facing the correct direction.

    NOTICE:
    Match the numbered connecting rod cap with the connecting rod.

  1. Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.

  1. Step 1:

    1. A164565
      Install and alternately tighten the bolts of the connecting rod cap in several steps.

      Torque:
      35 N*m{ 357 kgf*cm , 26 ft.*lbf }

      HINT:
      1. The connecting rod cap bolts are tightened in 2 progressive steps.
      2. If any connecting rod cap bolt is broken or deformed, replace it.

  1. Step 2:

    1. A158686E01
      Mark the front side of each connecting rod cap bolt with paint.

    2. Tighten the cap bolts 90°.

  1. A170350E01
    Check that the painted marks are now at a 90° angle to the front.

  1. Check that the crankshaft turns smoothly.


12. INSPECT CONNECTING ROD THRUST CLEARANCE

  1. A164562
    Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

    Standard thrust clearance:
    0.14 to 0.54 mm (0.00551 to 0.0213 in.)

    Maximum thrust clearance:
    0.60 mm (0.0236 in.)

    If the thrust clearance is more than the maximum, replace one or more connecting rods as necessary.
    If necessary, replace the crankshaft.

← REPLACEMENT (from Sep 2011)PRECAUTION (Sep 2011 – Dec 2011) →