B2311 Power Window Motor Malfunction
Diagnostic trouble codes · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The power window regulator motor is driven by operating the power window regulator switch. The power window regulator motor consists of the motor, regulator and ECU.This DTC is stored when the power window regulator motor has a malfunction, or the ECU built into the power window regulator motor determines that the fully closed window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.
- HINT:
- This DTC may be stored for all the windows.
- NOTICE:
- When the power window regulator motor is reinstalled or replaced, the power window control system must be initialized.
- After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be resumed by repeating the following operation at least 5 times:
- Close the power window by fully pulling up the power window switch and holding it in the auto up position.
- Open the power window by fully pushing down the switch.
- When the power window regulator motor is reinstalled or replaced, the power window control system must be initialized.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2311 |
|
|
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2311 |
|
|
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2311 |
|
|
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2311 |
|
|
INSPECTION PROCEDURE
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER WINDOW) |
Select the Active Test, use the intelligent tester to generate a control command, and then check that each power window regulator motor operates (Click here).
- CAUTION:
- Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.
D-Door Motor Tester Display
Test Part
Control Range
Diagnostic Note
Power Window
Driver side power window
OFF/UP/DOWN
-
P-Door Motor Tester Display
Test Part
Control Range
Diagnostic Note
Power Window
Front passenger side power window
OFF/UP/DOWN
-
RL-Door Motor Tester Display
Test Part
Control Range
Diagnostic Note
Power Window
Rear LH side power window
OFF/UP/DOWN
-
RR-Door Motor Tester Display
Test Part
Control Range
Diagnostic Note
Power Window
Rear RH side power window
OFF/UP/DOWN
-
- OK:
- Each power window motor operates.
Result Result
Proceed to
OK
A
NG (Front LH side power window)
B
NG (Front RH side power window)
C
NG (Rear LH side power window)
D
NG (Rear RH side power window)
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 2. PERFORM INITIALIZATION |
Initialize the power window regulator motor (Click here).
Check that each power window operates normally by opening and closing the window (Click here).
- OK:
- Each power window operates normally.
Result Result
Proceed to
OK
A
NG (Front LH side power window)
B
NG (Front RH side power window)
C
NG (Rear LH side power window)
D
NG (Rear RH side power window)
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 3. CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY |
Check that the power window components are installed correctly.
- OK:
- Power window components are installed correctly.
- HINT:
- When the power window components are installed correctly, the problem has been caused by battery disconnection while the ignition switch is ON or the motor being overheated.
|
|
||||
| OK | ||
| ||
