2011-2013 Land Cruiser · Service Manual Vehicle Interior

B1447/47 Rear Air Mix Damper Control Servo Motor Circuit on Driver Side

Diagnostic trouble codes · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The rear air mix damper servo motor (for driver side) sends pulse signals to indicate the damper position to the air conditioning amplifier assembly. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the rear air mix damper to the appropriate position. This adjusts the amount of air passing through the heater core after passing the evaporator and controls the temperature of the blown air.

HINT:
Confirm that no mechanical problem is present because this trouble code can be output when either a damper link or damper is mechanically locked.

DTC Code
DTC Detection Condition
Trouble Area
B1447/47
The rear air mix damper position does not change even if the air conditioning amplifier assembly operates the rear air mix damper servo motor.
  1. Rear air mix damper servo motor
  2. No. 2 air conditioning harness assembly
  3. Wire harness between No. 2 air conditioning harness assembly and air conditioning amplifier assembly
  4. Air conditioning amplifier assembly

WIRING DIAGRAM

E156903E09

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (REAR AIR MIX DAMPER SERVO MOTOR)
  1. Use the Data List to check if the servo motor is functioning properly.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/M Servo Targ Pulse (Rear D)
    Rear air mix damper servo motor target pulse /
    Min.: 9, Max.: 54 (for LHD)
    Min.: 8, Max.: 53 (for RHD)
    for LHD
    1. MAX COOL: 9 (pulse)
    2. MAX HOT: 54 (pulse)
    for RHD
    1. MAX COOL: 53 (pulse)
    2. MAX HOT: 8 (pulse)
    -

    OK:
    The display is as specified in the normal condition.



NG
Go to step 2
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

2. CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS - AIR CONDITIONING AMPLIFIER)
E156907E07
  1. Disconnect the K19 No. 2 air conditioning harness connector.

  1. Disconnect the E36 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K19-2 (RBUG) - E36-12 (RBUG)
    Always
    Below 1 Ω
    K19-3 (RBUS) - E36-13 (RBUS)
    K19-4 (RBBU) - E36-14 (RBBU)
    E36-12 (RBUG) - Body ground
    Always
    10 kΩ or higher
    E36-13 (RBUS) - Body ground
    E36-14 (RBBU) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK REAR AIR MIX DAMPER SERVO MOTOR (OPERATION)
  1. for LHD

    1. Replace the rear air mix damper servo motor LH (Click here).

  1. for RHD

    1. Replace the rear air mix damper servo motor RH (Click here).

      HINT:
      Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a normal one.


NEXT


4. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1447 is not output.



NG
REPLACE NO. 2 AIR CONDITIONING HARNESS ASSEMBLY (Click here)
OK

REPLACE REAR AIR MIX DAMPER SERVO MOTOR (Click here)


← B1447/47 Rear Air Mix Damper Control Servo Motor Circuit on Driver Side (Sep 2011 – Dec 2011)B1448/48 Passenger Side FACE Servo Motor Circuit (Sep 2011 – Dec 2011) →