2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Windshield Deicer does not Operate

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When the windshield deicer switch is turned on, a windshield deicer activation request signal is sent via the LIN communication line*1 or CAN communication line and UART communication line*2 to the air conditioning amplifier assembly. Then the air conditioning amplifier assembly operates the windshield deicer. When the on signal from the switch is received, the deicer relay (DEICER) is operated for 15 minutes. Also, if the off signal from the switch is received within 15 minutes, the deicer relay (DEICER) operation is stopped.

HINT:
*1: w/o Navigation System
*2: w/ Navigation System


WIRING DIAGRAM

B315403E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK FOR DTC
  1. *1: w/o Navigation System
  2. *2: w/ Navigation System
  1. Check if the CAN communication system*1 or CAN communication system*2 is functioning normally.

    1. LIN communication system: (Click here)
    2. CAN communication system (for LHD): (Click here)
    3. CAN communication system (for RHD): (Click here)
    Result 
    Result
    Proceed to
    DTC is not output
    A
    LIN DTC is output*1
    B
    CAN DTC is output (for LHD)*2
    C
    CAN DTC is output (for RHD)*2
    D



B
GO TO LIN COMMUNICATION SYSTEM (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (Click here)

D
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DEICER RELAY)
  1. Select the Active Test using the intelligent tester to generate a control command, and then check that the windshield deicer operates (Click here).

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Deicer Relay (Front)
    Deicer relay operation
    OFF or ON
    -

    OK:
    On intelligent tester screen, item changes between ON and OFF according to above chart.

    Result 
    Result
    Proceed to
    OK (w/o Navigation System)
    A
    OK (w/ Navigation System)
    B
    NG
    C



B
Go to step 5

C
Go to step 10
A


3. REPLACE AIR CONDITIONING CONTROL ASSEMBLY
  1. Temporarily replace the air conditioning control assembly with a new or normally functioning one (Click here).


NEXT


4. CHECK WINDSHIELD DEICER SYSTEM
  1. Turn the ignition switch ON.

  1. Check that pressing the windshield deicer switch illuminates the indicator and warms the front windshield surface.

  1. Check that after approximately 15 minutes, the indicator light turns off and the windshield deicer deactivates.

    OK:
    Windshield deicer system functioning normally.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

END (AIR CONDITIONING CONTROL ASSEMBLY IS DEFECTIVE)

5. CHECK NAVIGATION SYSTEM
  1. Check if the navigation system function properly (Click here).

    OK:
    Navigation system function properly.



NG
GO TO NAVIGATION SYSTEM (Click here)
OK


6. REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY
  1. Temporarily replace the air conditioning amplifier assembly with a new or normally functioning one (Click here).


NEXT


7. CHECK WINDSHIELD DEICER SYSTEM
  1. Turn the ignition switch ON.

  1. Check that pressing the windshield deicer switch illuminates the indicator and warms the front windshield surface.

  1. Check that after approximately 15 minutes, the indicator light turns off and the windshield deicer deactivates.

    OK:
    Windshield deicer system functioning normally.



NG
Go to step 8
OK

END (AIR CONDITIONING AMPLIFIER ASSEMBLY IS DEFECTIVE)

8. REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY
  1. Temporarily replace the multi-media module receiver assembly with a new or normally functioning one (Click here).


NEXT


9. CHECK WINDSHIELD DEICER SYSTEM
  1. Turn the ignition switch ON.

  1. Check that pressing the windshield deicer switch illuminates the indicator and warms the front windshield surface.

  1. Check that after approximately 15 minutes, the indicator light turns off and the windshield deicer deactivates.

    OK:
    Windshield deicer system functioning normally.



NG
REPLACE MULTI-DISPLAY ASSEMBLY (Click here)
OK

END (MULTI-MEDIA MODULE RECEIVER ASSEMBLY IS DEFECTIVE)

10. INSPECT DEICER RELAY

  1. B060778E76
    Remove the deicer relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω

    Result 
    Result
    Proceed to
    OK (w/ Rear Heater)
    A
    OK (w/o Rear Heater)
    B
    NG
    C



B
Go to step 15

C
REPLACE DEICER RELAY
A


11. CHECK HARNESS AND CONNECTOR (DEICER RELAY - AIR CONDITIONING AMPLIFIER AND BATTERY)

  1. B186157E01
    Remove the deicer relay from the engine room relay block.

  1. Disconnect the E36 air conditioning amplifier assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Deicer relay terminal 2 - Body ground
    Ignition switch ON
    11 to 14 V
    Deicer relay terminal 5 - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Deicer relay terminal 1 - E36-23 (FDEF)
    Always
    Below 1 Ω
    Deicer relay terminal 1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12. CHECK HARNESS AND CONNECTOR (DEICER RELAY - WINDSHIELD DEICER WIRE)

  1. B186158E01
    Remove the deicer relay from the engine room relay block.

  1. Disconnect the A23 windshield deicer wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-1 (B) - Deicer relay terminal 3
    Always
    Below 1 Ω
    Deicer relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13. CHECK HARNESS AND CONNECTOR (WINDSHIELD DEICER WIRE - BODY GROUND)

  1. A107917E27
    Disconnect the A23 windshield deicer wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-2 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14. CHECK WINDSHIELD DEICER WIRE

  1. A107917E29
    Disconnect the A23 windshield deicer wire connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A23-1 (B) - A23-2 (E)
    Ignition switch ON and deicer switch on
    11 to 14 V



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

REPLACE WINDSHIELD GLASS (Click here)

15. CHECK HARNESS AND CONNECTOR (DEICER RELAY - AIR CONDITIONING AMPLIFIER AND BATTERY)

  1. B188062E01
    Remove the deicer relay from the engine room relay block.

  1. Disconnect the E81 air conditioning amplifier assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Deicer relay terminal 2 - Body ground
    Ignition switch ON
    11 to 14 V
    Deicer relay terminal 5 - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Deicer relay terminal 1- E81-40 (FDEF)
    Always
    Below 1 Ω
    Deicer relay terminal 1- Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16. CHECK HARNESS AND CONNECTOR (DEICER RELAY - WINDSHIELD DEICER WIRE)

  1. B186158E01
    Remove the deicer relay from the engine room relay block.

  1. Disconnect the A23 windshield deicer wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-1 (B) - Deicer relay terminal 3
    Always
    Below 1 Ω
    Deicer relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


17. CHECK HARNESS AND CONNECTOR (WINDSHIELD DEICER WIRE - BODY GROUND)

  1. A107917E27
    Disconnect the A23 windshield deicer wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-2 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


18. CHECK WINDSHIELD DEICER WIRE

  1. A107917E29
    Disconnect the A23 windshield deicer wire connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A23-1 (B) - A23-2 (E)
    Ignition switch ON and deicer switch on
    11 to 14 V



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

REPLACE WINDSHIELD GLASS (Click here)


← Windshield Deicer does not Operate (Sep 2011 – Dec 2011)PRECAUTION (from Jan 2012) →