2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

B292994E01
  1. Put protective tape around the No. 2 instrument panel finish panel cushion.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 7 claws and remove the No. 2 instrument panel finish panel cushion.


4. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

B292995
  1. Remove the clip and screw.

  1. Detach the 8 claws.

  1. Disconnect the connectors, detach the 2 clamps and remove the lower instrument panel pad sub-assembly.


5. REMOVE NO. 1 INSTRUMENT PANEL FINISH PANEL CUSHION

B180004E02
  1. Put protective tape around the No. 1 instrument panel finish panel cushion.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 7 claws and remove the No. 1 instrument panel finish panel cushion.


6. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY RH

B180005
  1. Remove the clip and screw.

  1. Detach the 7 claws and remove the lower instrument panel pad sub-assembly.


7. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

B292996
  1. Detach the 7 claws.

  1. Disconnect the connectors and remove the lower center instrument cluster finish panel sub-assembly.


8. REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY

B183763
  1. Detach the 8 claws and remove the opening cover.


9. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY

B180307E02
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 6 claws.

  1. Disconnect the connector and remove the No. 3 instrument panel register.


10. REMOVE NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY

B181944E02
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 6 claws.

  1. Disconnect the connector and remove the No. 4 instrument panel register.


11. REMOVE MULTI-DISPLAY ASSEMBLY WITH BRACKET

  1. E247526
    Remove the 2 screws and 2 bolts.

  1. E247527
    Pull the multi-display assembly to detach the 2 clips and 6 claws on the backside of the multi-display assembly.

  1. Disconnect the connectors and remove the multi-display assembly.


12. REMOVE MULTI-MEDIA MODULE RECEIVER ASSEMBLY WITH BRACKET

  1. E247523
    Remove the 2 screws and 2 bolts.

  1. E247524
    Pull the multi-media module receiver assembly to detach the 5 claws on the backside of the multi-media module receiver assembly.

  1. Disconnect the connectors and remove the multi-media module receiver assembly.


13. REMOVE NO. 1 RADIO BRACKET

  1. E244798
    Remove the 3 bolts and No. 1 radio bracket.


14. REMOVE NO. 2 RADIO BRACKET

  1. E244799
    Remove the 3 bolts and No. 2 radio bracket.

← REMOVAL (Sep 2011 – Dec 2011)INSTALLATION (Sep 2011 – Dec 2011) →