2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Windshield Deicer does not Operate

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When the windshield deicer switch is turned on, a windshield deicer activation request signal is sent via the LIN communication line*1 or CAN communication line*2 to the air conditioning amplifier. Then the air conditioning amplifier operates the windshield deicer. When the on signal from the switch is received, the deicer relay (DEICER) is operated for 15 minutes. Also, if the off signal from the switch is received within 15 minutes, the deicer relay (DEICER) operation is stopped.

HINT:
*1: w/o Multi-display
*2: w/ Multi-display


WIRING DIAGRAM

B187445E02

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Check for DTC.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    LIN DTC is output
    B
    CAN DTC is output (for LHD)
    C
    CAN DTC is output (for RHD)
    D



B
GO TO LIN COMMUNICATION SYSTEM (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (Click here)

D
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DEICER RELAY)
  1. Select the Active Test using the intelligent tester to generate a control command, and then check that the windshield deicer operates.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Deicer Relay (Front)
    Deicer relay operation
    OFF or ON
    -
    Result 
    Result
    Proceed to
    Windshield deicer operates normally (w/o Multi-display)
    A
    Windshield deicer operates normally (w/ Multi-display)
    B
    Windshield deicer does not operate
    C



B
Go to step 5

C
Go to step 7
A


3. REPLACE AIR CONDITIONING CONTROL ASSEMBLY
  1. Temporarily replace the air conditioning control assembly with a new or normally functioning one (Click here).


NEXT


4. CHECK WINDSHIELD DEICER SYSTEM
  1. Turn the engine switch on (IG).

  1. Check that pressing the windshield deicer switch illuminates the indicator and warms the front windshield surface.

  1. Check that after approximately 15 minutes, the indicator light turns off and the windshield deicer deactivates.

    OK:
    Windshield deicer system functioning normally.



NG
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
OK

END (AIR CONDITIONING CONTROL ASSEMBLY IS DEFECTIVE)

5. REPLACE MULTI-DISPLAY
  1. Temporarily replace the multi-display with a new or normally functioning one (Click here).


NEXT


6. CHECK WINDSHIELD DEICER SYSTEM
  1. Turn the engine switch on (IG).

  1. Check that pressing the windshield deicer switch illuminates the indicator and warms the front windshield surface.

  1. Check that after approximately 15 minutes, the indicator light turns off and the windshield deicer deactivates.

    OK:
    Windshield deicer system functioning normally.



NG
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
OK

END (MULTI-DISPLAY IS DEFECTIVE)

7. INSPECT FUSE (DEICER)
  1. Remove the DEICER fuse from the engine room junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DEICER fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


8. INSPECT DEICER RELAY
B060778E76
  1. Remove the deicer relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω

    Result 
    Result
    Proceed to
    OK (w/ Rear air conditioning amplifier)
    A
    OK (w/o Rear air conditioning amplifier)
    B
    NG
    C



B
Go to step 13

C
REPLACE DEICER RELAY
A


9. CHECK HARNESS AND CONNECTOR (DEICER RELAY - AIR CONDITIONING AMPLIFIER AND BATTERY)
B186157E01
  1. Remove the deicer relay from the engine room relay block.

  1. Disconnect the E36 air conditioning amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Deicer relay terminal 2 - Body ground
    Engine switch on (IG)
    11 to 14 V
    Deicer relay terminal 5 - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Deicer relay terminal 1 - E36-23 (FDEF)
    Always
    Below 1 Ω
    Deicer relay terminal 1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. CHECK HARNESS AND CONNECTOR (DEICER RELAY - WINDSHIELD DEICER WIRE)
B186158E01
  1. Remove the deicer relay from the engine room relay block.

  1. Disconnect the A23 windshield deicer wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-1 (B) - Deicer relay terminal 3
    Always
    Below 1 Ω
    Deicer relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. CHECK HARNESS AND CONNECTOR (WINDSHIELD DEICER WIRE - BODY GROUND)
A107917E27
  1. Disconnect the A23 windshield deicer wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-2 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12. CHECK WINDSHIELD DEICER WIRE
A107917E29
  1. Disconnect the A23 windshield deicer wire connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A23-1 (B) - A23-2 (E)
    Engine switch on (IG) and deicer switch on
    11 to 14 V



NG
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
OK

REPLACE WINDSHIELD GLASS (Click here)

13. CHECK HARNESS AND CONNECTOR (DEICER RELAY - BATTERY AND AIR CONDITIONING AMPLIFIER)
B188062E01
  1. Remove the deicer relay from the engine room relay block.

  1. Disconnect the E81 air conditioning amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Deicer relay terminal 2 - Body ground
    Engine switch on (IG)
    11 to 14 V
    Deicer relay terminal 5 - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Deicer relay terminal 1- E81-40 (FDEF)
    Always
    Below 1 Ω
    Deicer relay terminal 1- Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14. CHECK HARNESS AND CONNECTOR (DEICER RELAY - WINDSHIELD DEICER WIRE)
B186158E01
  1. Remove the deicer relay from the engine room relay block.

  1. Disconnect the A23 windshield deicer wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-1 (B) - Deicer relay terminal 3
    Always
    Below 1 Ω
    Deicer relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15. CHECK HARNESS AND CONNECTOR (WINDSHIELD DEICER WIRE - BODY GROUND)
A107917E27
  1. Disconnect the A23 windshield deicer wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-2 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16. CHECK WINDSHIELD DEICER WIRE
A107917E29
  1. Disconnect the A23 windshield deicer wire connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A23-1 (B) - A23-2 (E)
    Engine switch on (IG) and deicer switch on
    11 to 14 V



NG
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
OK

REPLACE WINDSHIELD GLASS (Click here)


← DATA LIST / ACTIVE TEST (from Sep 2011)Windshield Deicer does not Operate (from Jan 2012) →